background image

Before beginning the installation, thoroughly & completely read these instructions & the enclosed  

driver’s WARNING NOTICE. Affix the WARNING decal in the passenger compartment in clear view 
of all occupants. Please refer to the Parts List to insure that all parts & hardware are received prior 
to the disassembly of the vehicle. If any parts are found to be missing, contact SKYJACKER® 

Customer Service at 318-388-0816 to obtain the needed items. If you have any questions or       

reservations about installing this product, call SKYJACKER® Technical Assistance at 318-388-0816. 

Make sure you park the vehicle on a level concrete or asphalt surface. Many times a vehicle is not 

level (side-to-side) from the factory & is usually not noticed until a lift kit has been installed, which 

makes the difference more visible. Using a measuring tape, measure the front & rear (both sides) 

from the ground up to the center of the fender opening above the axle. Record this information 

below for future reference.

Driver Side Front:   

 

 

 

Passenger Side Front: 

Driver Side Rear:   

 

 

 

Passenger Side Rear:

IMPORTANT NOTES: 

                                                                                                                                    

• This lift is determined from the amount of lift to the front of the vehicle, while only lifting the rear                                                                                                                                             

to a position level with the front. 

                                                                                                                        

 

If larger tires (10% more than the stock diameter) are installed, speedometer recalibration will be     

necessary.  Contact  your  local  Ford  dealer  or  an  authorized  dealer  for  details.                                                                                                                                         
                                                                                                                                        

 After installation a qualified alignment facility is required to align the vehicle to factory             

specifications. 

2004 - 2008 Ford F-150 2WD

6" Suspension Lift 

Installation Instructions

REquIRED TOOL LIST:

• Safety Glasses

• Metric / Standard Wrenches & Sockets

• Spring Compressor

• Floor Jack

• Jack Stands

• Measuring Tape

• Torque Wrench

• Transmission Jack

• 10,000 lb Shop Press

I-F4621 REV1 3-11

Pg 1

www.skyjacker.com

Содержание F4621A









Отзывы: