manualshive.com logo in svg

Skope PG1300VF, Руководство пользователя

Поделиться
Скачать
Skope PG1300VF Скачать руководство пользователя страница 15

15

SKOPE Pegasus Vertical Freezer - Integral

Servicing

User Manual

Cleaning

Cabinet

When necessary, wipe both the interior and exterior of the cabinet with a 
damp cloth. Ensure the cabinet is disconnected from the mains power 
supply before cleaning the cabinet. Periodic cleaning of the condenser coil 
is also required.

Condenser

Coil

The condenser coil is situated behind the unit front panel. The condenser 
coil 

MUST

 be kept clean for reliable operation and to minimise power 

consumption (a blocked condenser can double power consumption).
To ensure trouble free performance, the condenser coil should be brushed 
clean once a month and blown clean by qualified service personnel every 
six months.
Over time, dust may accumulate within the condenser that cannot be 
removed with a brush. if this occurs, contact SKOPE to arrange for a 
SKOPE Authorised Service Agent to clean the condenser with compressed 
air.

To access the condenser coil

CAUTION

Disconnect the cabinet from the mains power supply before 

cleaning the condenser coil or washing the cabinet.

1. Disconnect the chiller from the mains power supply.

2. Remove the refrigeration 

unit front panel from the 
cabinet by pulling the 
bottom of the panel out to 
unclip from the side 
panels and then lift the 
panel up off the cabinet. 
Refitting the front panel is 
a reversal of this 
procedure.

3. The condenser coil is now 

accessible for cleaning

.

Содержание PG1300VF


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды