manualshive.com logo in svg

Skope PG1300VF, Руководство пользователя

Поделиться
Скачать
Skope PG1300VF Скачать руководство пользователя страница 10

10

Operation

User Manual

SKOPE Pegasus Vertical Freezer - Integral

Controller

Operation

The operation of this freezer is controlled by a pre-programmed microproc-
essor. The Microprocessor display indicates the temperature of the cabinet 
ambient probe, except during a defrost where the temperature of the cabinet 
probe is locked in, and during an alarm condition.
At alarm activation, the display indicates the type of alarm signal, and an 
audible alarm sounds. The alarm can be muted by pressing the 

PRG/mute

 

key on the controller.

Controller

Alarms

A flashing LED indicates an alarm. The following is a list of alarms the 
controller displays:

* NOTE:

 Alarm ‘HI’ may activate during initial pull-down cycle, after being 

first powered up. The alarm can be muted and will automatically reset when 
the cabinet passes the alarm setpoint.

To reset an alarm

Alarm code Description

Faulty ambient probe

Faulty defrost probe

High pressure fault

Low (minimum) temperature alarm

High (maximum) temperature alarm

 *

Defrost timed out

Data acquisition failure

1. Clean the condenser radiator fins and remove any obstruction to the airflow.

2. Ensure the cabinet environment is below 32°C.

3. Unplug the cabinet from the power supply for 1 minute, then re-connect to the 

power supply.

4. Check cabinet product loading to ensure ventilation slots are not blocked and 

that product does not overhang the shelves.

5. If alarm persists, contact a SKOPE authorised refrigeration service agent.

Содержание PG1300VF


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды