Skoda Octavia III 2013 Скачать руководство пользователя страница 117

Страница: 117 / 172

– Move the pin -1- with the grinder of the inspection pin -3- in

such a way that the measurement pin of the inspection pin

-4- rests fully against the inner tread of the tyre.

– Remove the inspection pin and read off the tyre tread depth

(in mm) on the scale -2- (with tyre symbol) of the inspection

pin .

Note

♦

Check the tread depth at several points on the total tyre cir‐

cumference.

♦

The tread depth should be the same on the total tyre circum‐

ference.

♦

If the tread depth on the total tyre circumference significantly

varies, this is probably due to a wheel imbalance. The cus‐

tomer should be informed of the necessary repair measures.

5.6.3

Inspecting the tyre pressure (including

spare wheel), if necessary correcting

pressure

Special tools and workshop equipment required
♦ Tyre pressure tester e.g. VAS 5216
Tyre pressure values

Caution

♦ During pre-sales inspection, the tyres on the front and real

axles must be inflated to the “partial load” pressure vale.

♦ On Green Line vehicles, the value “Partial load/Comfort

applies.”

The pressure values are also indicated on a sticker,which is

affixed to the inside of the fuel filler flap.
The tyre pressure values apply only to the tyres when cold.
Do not reduce the higher tyre pressure of warm tyres.
The tyre pressure in the spare wheel should correspond to the

highest specified tyre pressure of the respective vehicle type.
After each tyre pressure correction the calibration of the “tyre

inspection

display”

must

performed

⇒ “5.8 Tyre inspection display: Calibration”, page 123

Octavia III 2013 ➤ , Octavia III 2014 ➤

Maintenance - Edition 12.2014

5. Chassis

113

ProCarManuals.com

Содержание Octavia III 2013













































































































































































Результаты поиска

Содержание Octavia III 2013

Отзывы:

Похожие инструкции для Octavia III 2013

Бренды по названию

Популярные бренды

Skoda Octavia III 2013, Руководство по обслуживанию

Результаты поиска

Содержание Octavia III 2013

Отзывы:

Похожие инструкции для Octavia III 2013

Бренды по названию

Популярные бренды