background image

 

squirt a little longer paint pattern than the electrical system commands. The "hanging on" also 
causes some variation in stripe length with truck speed. The effect will be most evident at high 
truck speed. 
If a paint gun hangs on for .050 second, the error will be 1.1 foot at 15 mph. 
 
The STRIPE length can be calibrated by adjusting the GUN FACTOR for each gun. The Gun 
Factor number delays the turn-on time of the paint to equal the turn-off time of the paint gun 
when adjusted correctly. 
 
Find the instructions for setting GUN FACTOR in the SETUP MENU. 

 
 
BEAD REGISTRATION  (BEADS MENU)

 

 
These controls help to position the beads over the paint pattern. The edges of the bead pattern 
can be moved relative to the paint pattern.  The BEGINNING control affects the "turn on" part 
of the bead pattern. The END control affects the "turn off" part of the bead pattern. 
 
The numbers represent tenths-of-a-foot adjustments, (+) means move the beads forward on the 
pavement, (-) means move the beads backwards on the pavement. The correction is not perfect, 
it depends on speed and agility of your paint guns.  
 

|<                                                 Stripe                                                  >| 

       <   -  Beginning   +  >                                                                                <      -      END     +     >

 

 
 
 

Direction of Motion                      >

 

 
Bead registration overlay correction at the beginning and end of the stripe. 
 
To adjust the BEAD coverage, follow the instructions to enter the BEADS MENU. 
 
 

Adjust the BEGIN BEADS number with the (

+

) and (

-

) buttons.  

 
(A negative number will cause the bead gun to come on sooner, and a positive number will cause 
the bead gun to turn on after the paint gun.) 
 
Press the 

NEXT

 button to adjust the turn off time of the beads. 

 
 

Adjust the END BEADS number with the (

+

) and (

-

) buttons.  

 
(A negative number will cause the bead gun to turn off sooner, and a positive number will cause 
the bead gun to turn off after the paint gun.) 

 
 
 
 
 
 

Содержание MST-02













Отзывы: