7.
“SAVE THESE INSTRUCTIONS”
Model Number . . . . . . . . . . . . . . . . . . . . . . . . .SPT64MTA
Wheel ø . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14” (355mm)
Arbor ø . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1” (25.4mm)
Voltage Rating . . . . . . . . . . . . . . . . . . . . . . .120 V~ 60 Hz
Amperage Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 A
No Load Speed (n
0
) . . . . . . . . . . . . . . . . . . . . . . .3800/min
Electrical Requirements
• Connect this saw to a 120V, 15-amp branch circuit with a 15-
amp fuse or circuit breaker. Using the wrong size fuse can
damage the motor.
• Fuses may “blow” or circuit breakers may trip frequently if
motor is overloaded. Overloading can occur if you feed the
wheel into the workpiece too rapidly or start and stop too
often in a short time.
• Most motor troubles may be traced to loose or incorrect
connections, overload, low voltage (such as small size wire
in the supply circuit or too overly long supply circuit wire).
Always check the connections, the load and the supply
circuit whenever motor does not work well.
Double Insulated Tools
Double Insulation is a design concept used in elec tric
power tools which eliminates the need for the three wire
grounded pow er cord and grounded power supply system. It is
a recog nized and approved system by Underwriter’s Lab -
oratories, CSA and Federal OSHA authorities.
IMPORTANT:
Servicing of a tool with double insulation re -
quires care and knowledge of the system and should be
performed only by a qualified service technician.
WHEN SERVICING, USE ONLY IDENTICAL REPLACE -
MENT PARTS.
POLARIZED PLUGS. To reduce the risk of electric shock,
your tool is equipped with a po lar ized plug (one blade is wider
than the other), this plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician to install the
proper outlet. To reduce the risk of electric shock, do not
change the plug in any way.
Extension Cords
Replace damaged cords immediately. Use of damaged
cords can shock, burn or elec trocute.
Always use proper extension cord. If an extension cord is
necessary, a cord with adequate size con ductors should be
used to prevent excessive voltage drop, loss of power or over -
heating. The table shows the correct size to use, de pending
on cord length and nameplate amperage rating of tool. If in
doubt, use the next heavier gauge. Always use U.L. and CSA
listed extension cords.
RECOMMENDED SIZES OF EXTENSION CORDS
120 VOLT ALTERNATING CURRENT TOOLS
NOTE:
The smaller the gauge number, the heavier the cord.
Tool’s
Ampere
Rating
Cord Size in A.W.G.
Wire Sizes in mm
2
3-6
6-8
8-10
10-12
12-16
25 50 100 150 15 30 60 120
18 16 16 14 .75 .75 1.5 2.5
18 16 14 12 .75 1.0 2.5 4.0
18 16 14 12 .75 1.0 2.5 4.0
16 16 14 12 1.0 2.5 4.0 —
14 12 — — — — — —
Cord Length in Feet
Cord Length in Meters
Motor Specifications & Electrical Requirements
1619PA9299 09-15 SPT64MTA.qxp_SPT64MTA 9/14/15 7:02 AM Page 7
