Ski-Doo Skandic LT 2002 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 119

background image

64

OPERATING INSTRUCTIONS

Principle of Operation

Propulsion

Depressing throttle lever increases engine RPM causing the drive
pulley to engage. For most models engine RPM must be between
2500 and 4200 before drive pulley engagement will occur.

Outer sheave of drive pulley moves toward inner sheave, forcing
drive belt to move upward on the drive pulley and simultaneously
forcing the sheaves apart on the driven pulley.

The driven pulley senses the load on the track and limits the belt
movement. The result is a continuous change in the ratio of the two
pulleys which maximizes acceleration and forward movement of the
vehicle.

Power is transferred to the track through the chaincase or gearbox and
drive axle.

Turning

Handlebar controls the direction of travel of the vehicle. As the han-
dlebar is rotated to right or left, the skis are turned in the direction of
intended travel.



WARNING

Proceed with pre-operation check list before riding.



WARNING

Do not operate engine with hood open or belt guard removed.



WARNING

Always use a mechanical snowmobile stand to properly sup-
port vehicle during any track verification. Slowly accelerate en-
gine in order to rotate track at very low speed when it is not on
ground.



WARNING

Fast reverse while turning, could result in loss of stability.

Mmo2002-001a.book Page 64 Friday, January 12, 2001 1:56 PM

«
...
64
65
66
67
68
...
»

Содержание Skandic LT 2002
























































































































Отзывы:

Нет отзывов

Похожие инструкции для Skandic LT 2002

DRIFTER 10-0550

Бренд: Kolpin Страницы: 17

BOSS RT FATBOY 1026RT RR

Бренд: Meyer Страницы: 44

Polar Trailer 10537

Бренд: Clam Страницы: 7

Бренд: Landoll Страницы: 82

Бренд: Suzuki Страницы: 140

2010 Ranger RZR 800 EFI

Бренд: Polaris Страницы: 352

Бренд: E-TON Страницы: 35

Бренд: Bad Boy Страницы: 64

Бренд: Xingyun Страницы: 92

Бренд: Landoll Страницы: 64

Бренд: Parklands Страницы: 66

WaveRunner SuperJet 2020

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 184

Grizzly YFM600FWAM

Бренд: Yamaha Страницы: 164

Бренд: Yamaha Страницы: 182

Бренд: Yamaha Страницы: 10

Бренд: Yamaha Страницы: 30

WARRIOR YFM350XP

Бренд: Yamaha Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды