Ski-Doo Skandic LT 2002 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 119

background image

35

Manual Starting

Key operated, 2-position switch. To start the engine, first turn the key
to ON position then, pull rewind starter grip. To stop the engine, turn
the key to OFF position.

Electric Starting

Key operated, 3-position switch. To start engine, turn key to START
position and hold until engine has started. See illustration above.

CAUTION:

Do not hold key at START position more than 15 sec-

onds. A rest period should be observed between the cranking
cycles to let starter cool down. Holding key in START position
when engine has started could damage starter mechanism.

Release key immediately when engine has started. Key returns to
ON position as soon as it is released.

If engine does not start on first try, turn key back to OFF position
before restarting. To stop engine, turn key to OFF position.

NOTE:

Engine may be manually started with rewind starter if necessary.

If starter does not operate, check starting system fuse condition.
Refer to

Starting System Fuse

below.

7) Tether Cut-Out Switch

All Models

General

The tether cut-out system shuts-off engine if the driver accidently falls
off the vehicle.

Mmo2002-001a.book Page 35 Friday, January 12, 2001 1:56 PM

«
...
35
36
37
38
39
...
»

Содержание Skandic LT 2002
























































































































Отзывы:

Нет отзывов

Похожие инструкции для Skandic LT 2002

Бренд: Skylift Страницы: 407

Бренд: UtilityDump Страницы: 13

Бренд: Arctic Cat Страницы: 123

Бренд: E-Z-GO Страницы: 212

1988 TRX 300 FW

Бренд: Honda Страницы: 84

Бренд: Ski-Doo Страницы: 162

Dune Buggy GT250

Бренд: Hammerhead Страницы: 25

BIG BEAR YFM400NN

Бренд: Yamaha Страницы: 161

BIG BEAR YFM400NC

Бренд: Yamaha Страницы: 162

BANSHEE YFZ350Y

Бренд: Yamaha Страницы: 142

Big Bear 400 YFM40FBB

Бренд: Yamaha Страницы: 156

Бренд: Yamaha Страницы: 156

BEARTRACKER YFM250XN

Бренд: Yamaha Страницы: 156

Бренд: Yamaha Страницы: 140

Бренд: Yamaha Страницы: 167

BIG BEAR YFM400FWS

Бренд: Yamaha Страницы: 173

BANSHEE 350 YFZ350Z

Бренд: Yamaha Страницы: 146

Бренд: Yamaha Страницы: 163

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды