Ski-Doo 1997 FORMULA 500 Скачать руководство пользователя страница 56

Страница: 56 / 126

SUSPENSION ADJUSTMENTS

All Models Except Tundra II LT and Skandic WT/SWT

For factory recommended adjustments refer to decal on pulley
guard.

This decal describes settings for optimum comfort according to load
for your Ski-Doo model.

General

All Models

Snowmobile handling and comfort depend upon suspension adjust-
ments.

Choice of suspension adjustments vary with carrying load, driver’s
weight, personal preference, riding speed and field condition.

NOTE :

Some adjustments may not apply to your snowmobile.

Use special keys in tool kit.

TYPICAL

1. Rear springs for comfort
2. Center spring for steering behavior
3. Stopper strap for snowmobile weight transfer
4. Acceleration and control modulator (ACM) – Handling
5. Front spring for handling
6. Ski stopper for stability

A03H1FB

Содержание 1997 FORMULA 500































































































































Результаты поиска

Содержание 1997 FORMULA 500

Отзывы:

Похожие инструкции для 1997 FORMULA 500

Бренды по названию

Популярные бренды

Ski-Doo 1997 FORMULA 500, Руководство оператора

Результаты поиска

Содержание 1997 FORMULA 500

Отзывы:

Похожие инструкции для 1997 FORMULA 500

Бренды по названию

Популярные бренды