Ski-Doo 1997 FORMULA 500 Скачать руководство пользователя страница 102

Страница: 102 / 126

100

Wear and Condition of Skis and Runners

Check the condition of the skis, ski runners and ski runner carbides
(if so equipped). If worn, contact your authorized dealer.

Exhaust System

The tail pipe of the muffler should be centered with the exit hole in
the bottom pan. If must be free of rust or leaks.

The exhaust system is designed to reduce noise and to improve the
total performance of the engine. If any exhaust system component
is removed from the engine, severe engine damage will result.

Air Filter Cleaning

Tundra II LT

Air filter is located on lower side portion of air intake silencer. Lift
hood and remove belt guard. Gently pull air filter sideward.

Ensure it is clean and dry. Shake snow out. Clean with a solvent and
dry as necessary.

◆

WARNING

Excessively worn skis and/or ski runners will affect proper
snowmobile control.

Содержание 1997 FORMULA 500































































































































Результаты поиска

Содержание 1997 FORMULA 500

Отзывы:

Похожие инструкции для 1997 FORMULA 500

Бренды по названию

Популярные бренды

Ski-Doo 1997 FORMULA 500, Руководство оператора

Результаты поиска

Содержание 1997 FORMULA 500

Отзывы:

Похожие инструкции для 1997 FORMULA 500

Бренды по названию

Популярные бренды