SKF MAX-1-1-115-IF105-R-V2 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 47

SKF MAX-1-1-115-IF105-R-V2 Скачать руководство пользователя страница 28

28

10 IF-105 operation

10.1 Normal mode

10.1.1 Functions

Display power saving mode

In normal mode, the display shifts to power saving mode when no buttons have been used for ten (10)
minutes. In power saving mode only the decimal points are blinking on the display. Lubrication events are per-
formed according to the set values. The display returns to normal mode if any button is pressed or if there is
an alarm.

Interval counting

In normal mode the display shows the time elapsed since the last pressurization as hours and minutes. Green
LED-signal for line L1 or L2 shows which line has been pressurized last.

Interval time is counted always, except when

•

channel is in alarm mode

•

interlocking switch of the channel is closed

•

channel is closed (maximum pressurization time = 0)

Pressurization

Pressurization time is displayed as seconds. Green LED-signal for line L1 or L2 shows the line to be pressur-
ized. Green LED-signal P indicates that pressurization is in progress.

Pressurization can be stopped with the SET button.

Pressurization time display and setting can be changed from seconds to minutes with factory setting parame-
ter Prt. When the pressurization time is displayed as minutes all the decimal points are lit on the display.

Extra lubrication

Extra lubrication can be started if the channel is not currently in alarm mode, closed or pressurizing.

Extra lubrication is started in normal mode with the SET button, when the display shows the time elapsed
since the last pressurization.

In a DuoFlex lubrication system both lines are pressurized once. The next line in the set pressurization se-
quence is pressurized first. In a MonoFlex and a ProFlex lubrication system the line is pressurized once.

Extra lubrication can be stopped with the SET button.

In pressure transmitter operation, the line pressure discharge is measured. New pressurization starts only af-
ter pressure in the lines is below the set low limit value.

In pressure switch operation, the system waits for line pressure discharge. New pressurization starts only after

«
...
26
27
28
29
30
...
»

Содержание MAX-1-1-115-IF105-R-V2
















































Отзывы:

Нет отзывов