Sitecom KAMULTSSVDA Скачать руководство пользователя страница 8

Страница: 8 / 65

Sitecom Wireless Network UMTS Router 54G WL-610

3.2 Procedure for Hardware Installation

3.2.1 Decide where to place your Wireless Broadband Router

You can place your Wireless Broadband Router on a desk or other flat surface, or you can

mount it on a wall. For optimal performance, place your Wireless Broadband Router in the

center of your office (or your home) in a location that is away from any potential source of

interference, such as a metal wall or microwave oven. This location must be close to power

and network connection.

3.2.2 Setup LAN connection

•

Wired LAN connection: connects an Ethernet cable from your computer’s Ethernet

port to one of the LAN ports of this product.

•

Wireless LAN connection: locate this product at a proper position to gain the best

transmit performance.

Figure 2-3 Setup of LAN and WAN connections for this product.

3.2.3 Setup WAN connection

Prepare an Ethernet cable for connecting this product to your cable/xDSL modem or Ethernet

backbone. Figure 2-3 illustrates the WAN connection.

3.2.4 Power on

Connecting the power cord to power inlet and turning the power switch on, this product will

automatically enter the self-test phase. When it is in the self-test phase, the Power LED will

Содержание KAMULTSSVDA


































































Результаты поиска

Содержание KAMULTSSVDA

Отзывы:

Похожие инструкции для KAMULTSSVDA

Бренды по названию

Популярные бренды

Sitecom KAMULTSSVDA, Руководство пользователя

Результаты поиска

Содержание KAMULTSSVDA

Отзывы:

Похожие инструкции для KAMULTSSVDA

Бренды по названию

Популярные бренды