background image

UPA-61W

42. BATTERY 

These LEDs are used to indicate the power of the battery. 

43. EXT. DC 12V 

When the AC and battery are out of power, you can use the 
EXT. DC 12V supply to the unit.

44. POWER AMP. Switch    

Turn the Power AMP switch on "OFF" position, the EXT. DC 
output will be cut off, and the battery will store the power; 
this switch on "ON" position, the EXT. DC supply will work 
on normal condition. 

45. SPEAKON Connector     

This  connector  is  used  to  connect  with  the  passive 
speakers. It is configured with a speakon connector. You 
can determine the signal that is out put to this jack.

NOTE:

 In order to avoid damaging your built-in amplifier, 

please pay more attention to the impedance of speaker. 
Lower load impedances are not permitted.

46. CLIP LED

When the output signal distortion exceeds 0.5%, then the 
red LED (Clip) indicator will blink. It will warn you that the 
levels of the input signal are too high and may cause distortion. Please attenuate the level of the input signal. 

47. TO MIXER

Put the Mixer on the bracket to adjust the volume, you can insert the connector into the TO MIX jack, and the unit can work on 
normal condition.

48. PHONE Jack & SPEAKON Connector 

 

These jacks are used to connect UPA-612W-615 passive speakers. They are configured with a speakon connector and 1/4” 
phone jack. You can determine the signal that is outputted to these jacks.  

NOTE: 

In order to avoid damaging your built-in amplifier, please pay more attention to the impedance of speaker. Lower load 

impedances are not permitted.

3.5 WIRELESS MICROPHONE SYSYTEM

Diversity Receiver 
49. Antenna 

The antenna receives signal from transmitter. Make sure the antenna is fully extended vertically for receiving best effect. Fold 
both antennas inward for the convenience of transporting. 

50. AF-LEVEL Indicator 

These LEDs indicate the incoming status of the audio signal. The four green LEDs light up indicate normal condition. When the 
audio signal from microphone approaches clipping level the red LED indicator lights up, If no LED lights up, there is little or even 

40

39

38

41

43

42

46

47

45

44

Содержание UPA-612W

















Отзывы: