22
PARTS LIST 07625
Ref. No.
Description
Sip Part No. Ref. No.
Description
Sip Part No.
1.
Screw M5x18
WK05-00095
27.
Mains lead
WK05-00118
2.
Left wheel cover
WK05-00096
28.
Right spark arrestor
WK05-00119
3.
Nut (12mm left)
WK05-00004
29.
Right eye shield arm
WK05-00120
4.
Flange
WK05-00097
30.
Eye shield
WK05-00121
5.
Coarse wheel 36 grit
(150 x 20 x12.7)
17638
31.
Right tool rest
WK05-00122
6.
Screw M5x10
WK05-00098
32.
Right cover plate
WK05-00123
7.
Left wheel guard
WK05-00099
33.
Fine wheel 60 grit
(150 x 20 x 12.7)
17632
8.
Left spark arrestor
WK05-00100
34.
Nut (12mm right)
WK05-00006
9.
Washer 5mm
WK05-00101
35.
Right cover
WK05-00124
10.
Spring washer 5mm
WK05-00102
36.
Mains lead grommet
WK05-00125
11.
Screw M5x8
WK05-00103
37.
Lock washer
WK05-00126
12.
Bolt M5x20
WK05-00104
38.
Screw M4x8
WK05-00127
13.
Nut 5mm
WK05-00105
39.
Base
WK05-00128
14.
Left tool rest
WK05-00106
40.
Strain relief bush
WK05-00129
15.
Washer 5mm (big)
WK05-00107
41.
Capacitor 8mf
WK05-00130
16.
Lock knob
WK05-00187
42.
Capacitor support
WK05-00131
17.
End cap
WK05-00108
43.
Nut 8mm
WK05-00132
18.
Bolt M6x14
WK05-00109
44.
Screw M4x8
WK05-00133
19.
Washer 6mm
WK05-00110
45.
Rubber foot
WK05-00134
20.
Bracket
WK05-00111
46.
Bottom cover
WK05-00135
21.
Left eye shield arm
WK05-00112
47.
Bolt M8x22
WK05-00136
22.
Eye shield holder
WK05-00113
48.
Screw M5x16
WK05-00137
23.
Spring washer
WK05-00114
49.
NVR switch KJD18
WK05-00138
24.
Bearing
WK05-00115
50.
Wire wheel
WK05-00139
25.
Stator
WK05-00116
51.
Washer for wire wheel
WK05-00140
26.
Rotor
WK05-00117
7
Grinding produces particles which can become airborne and have
the potential to be highly toxic; always wear a face mask when op-
erating the grinder.
When using the grinder always ensure the operator as well as those
in the area wear ear protection, particularly during periods of ex-
tended use.
SAFETY INSTRUCTIONS...cont
Caution:
The warnings and cautions mentioned in this user manual can not
cover all possible conditions and situations that may occur. It must be under-
stood by the operator that common sense and caution are factors which can-
not be built into this product, but must be applied.
When using the grinder always ensure the operator as well as those
in the area wear eye protection.
Only use grinding wheels that are rated for the correct speed.
Do not overload the grinding wheel; stalling the machine will shorten its life.
After fitting new grinding wheel, leave machine running for at least one minute.
If the wheel is faulty it will break during this test period.
Stand to the side of the grinder during initial start up.
Use a wheel dresser only to remove burrs on the grinding wheel.
If the grinder is used in a place of work all rules and laws etc. relating to the use
of portable electrical appliances should be followed.
