16
PARTS LIST - 03647
Ref. No.
Description
SIP Part No.
Ref. No.
Description
SIP Part No.
1-1
Frame
HY01-00566
1-19
Shaft
HY01-00573
1-2
Front wheel
HY01-00567
1-20
Washer
HY01-00529
1-3
Washer
HY01-00512
1-21
Pin
HY01-00530
1-4
Snap ring
HY01-00513
1-22
Connection bar
HY01-00574
1-5
Grease nipple
HY01-00514
1-23
Spring
HY01-00575
1-6
Rod link
HY01-00568
1-24
Snap ring
HY01-00533
1-7
Bolt
HY01-00516
1-25
Shaft
HY01-00576
1-8
Saddle
HY01-00569
1-26
Metal plate
HY01-00577
1-9
Lock washer
HY01-00518
1-27
Lock washer
HY01-00536
1-10
Nut
HY01-00519
1-28
Snap ring
HY01-00537
1-11
Spring
HY01-00570
2-1 to 2-30
Complete pump
HY01-00578
1-12
Bolt (M10x25)
HY01-00521
3-1
Handle base
HY01-00579
1-13
Bolt (M10x16)
HY01-00522
3-2
Foot pedal
HY01-00580
1-14
Snap ring
HY01-00523
3-3
Nut M10
HY01-00541
1-15
Shaft
HY01-00571
3-4
Washer
HY01-00542
1-16
Rear castor
HY01-00572
3-5
Bolt (M10x35)
HY01-00543
1-17
Nut
HY01-00526
3-6 to 3-21
Handle complete
HY01-00581
1-18
Snap ring
HY01-00527
N/A.
Repair kit
HY01-00582
5
SAFETY INSTRUCTIONS….cont
WARNING!
Only operate on a level and stable surface and never use on soft ground
where the Floor Jack is likely to “sink” whilst in operation.
NEVER STAND ON THE FLOOR JACK:
The Floor Jack is not designed for this purpose.
DO NOT
dismantle or tamper with the Floor Jack, as this may be dangerous and will
invalidate the warranty.
ALWAYS
ensure the load is central on the saddle.
If a problem with the Floor Jack is experienced or suspected stop using the Floor
Jack
immediately
and contact your distributor for repair.
Do not attempt to lift a load that exceeds the rated capacity of the Floor Jack.
Do not attempt to lift a load beyond the maximum height of the Floor Jack.
This Floor Jack is a lifting device only.
Immediately after lifting, support the load with a pair of appropriately rated jack
stands.
Never work on, under or around a load supported only by the Floor Jack.
Regularly inspect and lubricate the Floor Jack, ensuring that it is in good working or-
der and condition.
Always ensure that the work area is clean and tidy, free from unrelated materials and
has adequate lighting.
When lifting a vehicle ensure a minimum distance of 0.5m between vehicle and
static objects such as doors, walls, etc. to allow for tilting during jacking.
Ensure that all persons are out of the vehicle before jacking.
DO NOT
enter the vehicle whilst it is supported on the Floor Jack or axle stands.
Check vehicle weight and recommended lifting points by referring to the vehicle’s
manual. Ensure that the lifting point is not corroded.
DO NOT
allow the vehicle to move, or try to start the engine, during jacking.
DO NOT
start the engine when vehicle is jacked up.
DO NOT
jack a vehicle if this may result in the spillage of fuel, battery acid, or other
dangerous substances.
Check that the Floor Jack saddle is centred and stable on the lifting point (off-centre
loads can slip).
Position the Floor Jack to avoid operating it from under vehicle.
Keep hands, limbs etc. clear of moving parts during the raising and lowering of the
vehicle.
DO NOT
top-up the Floor Jack with brake fluid, or other oil types; use only hydraulic
oil.
DO NOT
adjust the safety overload valve.
Ensure that there are no persons or obstructions beneath the load before lowering.
Clean and stow the Floor Jack correctly, with the ram in the down position,
DO NOT
leave it extended; ensure storage area is dry.
IMPORTANT!
Ensure that you can see the saddle and jacking point throughout the
jacking operation in case there is any relative movement.
Failure to follow the warnings in this manual, may result in personal injury and/or prop-
