8
ELECTRICAL CONNECTION
WARNING!
It is the responsibility of the owner and the operator to read, understand
and comply with the following:
You must check all electrical products, before use, to ensure that they are safe.
You must inspect power cables, plugs, sockets and any other connectors for wear or
damage.
You must ensure that the risk of electric shock is minimised by the installation of appro-
priate safety devices; A residual current circuit Breaker (RCCB) should be incorporated
in the main distribution board. We also recommend that a residual current device
(RCD) is used. It is particularly important to use an RCD with portable products that are
plugged into a supply which is not protected by an RCCB. If in any doubt consult a
qualified electrician.
Connecting to the 1 phase power supply:
This SIP bandsaw is fitted with a standard 230v ~ 13 amp type plug. Before using the
bandsaw, inspect the mains lead and plug to ensure that neither are damaged. If
any damage is visible have the bandsaw inspected / repaired by a suitably qualified
person. If it is necessary to replace the plug a heavy duty impact resistant plug would
be preferable.
The wires for the 1 phase plug are coloured in the following way:
Yellow / green
Earth
Blue
Neutral
Brown
Live
As the colours of the wires may not correspond with the markings in your plug, pro-
ceed as follows: The wire which is coloured blue, must be connected to the terminal
marked with N or coloured black. The wire which is coloured brown, must be connect-
ed to the terminal, which is marked L or coloured red. The wire which is coloured yel-
low / green should be connected to the terminal which is coloured the same or
marked
Always secure the wires in the plug terminal carefully and tightly. Secure the cable in
the cord grip carefully.
Connecting to the 3 phase power supply:
The 3ph bandsaw comes with no plug fitted, the cable will have 3 phases and an
earth, this should be, where possible, hard wired into the mains board, always use a
29
PARTS LIST
Ref. No.
Description
SIP Part No.
Ref. No.
Description
SIP Part No.
1.
Bottom pan
WK04-00001
37.
Hose
WK04-00025
2.
Left leg
WK04-00002
38.
Handle
WK04-00026
3.
Right leg
WK04-00003
39.
Vice hand-wheel
WK04-00027
4.
Front panel
WK04-00004
40.
Bolt M6x6
WK04-00028
5.
Middle pan
WK04-00005
41.
Key 5x20
WK04-00029
6.
Wheel 125x12mm
WK04-00006
42.
Lead screw
WK04-00030
7.
Pin 25x3
WK04-00007
43.
Acme nut seat
WK04-00031
8.
Axle
WK04-00008
44.
Bolt M6x16
WK04-00010
14.
Hydraulic cylinder
WK04-00009
45.
Acme nut
WK04-00032
17.
Bolt M6x16
WK04-00010
46.
Pin
WK04-00033
18.
Washer M6
WK04-00011
47.
Spring screw
WK04-00034
19.
Nut M6
WK04-00012
48.
Bolt M5x8
WK04-00035
20.
Bolt M8x16
WK04-00013
49.
End of cut
microswitch housing
WK04-00036
21.
Washer M8
WK04-00014
50.
End of cut microswitch
WK04-00037
22.
Nut M8
WK04-00015
51.
Washer M6
WK04-00011
23.
Bolt M6x20
WK04-00016
52.
Bolt M6x12
WK04-00038
25.
Filter
WK04-00017
53.
Thumb screw
for cut off stop
WK04-00039
26.
Nut M6
WK04-00012
54.
Cut off stop
WK04-00040
27.
Bolt M8x30
WK04-00018
55.
Cut off stop shaft
WK04-00041
28.
Washer M8
WK04-00014
56.
Bolt M8x16
WK04-00013
29.
Nut M8
WK04-00015
57.
Washer M8
WK04-00014
31.
Coolant tank
WK04-00020
58.
Nut M8
WK04-00015
32.
Hose
WK04-00021
59.
Support plate
WK04-00042
33.
Coolant pump 1 phase
WK04-00022
60.
Bolt M8x30
WK04-00018
33.
Coolant pump 3 phase
WK04-00330
61.
Bed
WK04-00043
34.
Bolt M6x16
WK04-00010
62.
Lever lock
WK04-00044
35.
Hose fitting
WK04-00023
63.
Bolt M10x35
WK04-00045
36.
Hose clamp
WK04-00024
64.
Washer M10
WK04-00046
