30
Ref. No.
Description
SIP Part No.
Ref. No.
Description
SIP Part No.
65.
Movable vice jaw
WK04-00047
92.1.
Washer M8
WK04-00014
66.
Bolt M12x40
WK04-00048
93.
Bolt M10x45
WK04-00065
67.
Washer M12
WK04-00049
94.
Washer M10
WK04-00046
68.
Fixed vice jaw
WK04-00050
94.1.
Nut M10
WK04-00052
69.
Bolt M10x20
WK04-00051
95.
Bolt M8x16
WK04-00013
70.
Washer M10
WK04-00046
96.
Washer M8
WK04-00014
71.
Nut M10
WK04-00052
97.
Blade guard
WK04-00066
72.
Spring support
WK04-00053
97.1.
Pulley cover
WK04-00067
73.
Bolt
WK04-00054
98.
Bolt M8x16
WK04-00013
74.
Spring
WK04-00055
99.
Washer M8
WK04-00014
75.
Bolt M10x40
WK04-00056
100.
Bolt M8x20
WK04-00068
76.
Nut M10
WK04-00052
101.
Large washer M8
WK04-00069
77.
Bolt M10x35
WK04-00045
102.
Bearing 6203ZZ
WK04-00070
78.
Pivot arm plate
WK04-00057
103.
Idle blade pulley
WK04-00071
79.
Pivot arm
WK04-00058
103.1.
Drive blade pulley
WK04-00072
80.
Bed shaft
WK04-00059
104.
Blade
Contact
Distributor
81.
Sleeve
WK04-00060
105.
Idle pulley sleeve
WK04-00073
82.
Washer M16
WK04-00061
106.
Saw bow
WK04-00074
83.
Nut M10
WK04-00052
107.
Blade tensioning knob
WK04-00075
84.
Support
WK04-00062
108.
Spring
WK04-00076
85.
Bolt M10x40
WK04-00056
109.
Plate
WK04-00077
86.
Nut M10
WK04-00052
110.
Washer M6
WK04-00011
87.
Bolt M10x35
WK04-00045
111.
Bolt M6x16
WK04-00010
88.
Washer M10
WK04-00046
112.
Idle pulley shaft
WK04-00078
89.
Bottom support for
hydraulic cylinder
WK04-00063
113.
Idle pulley shaft seat
WK04-00079
90.
Bolt M8x30
WK04-00018
114.
Pin 4x20
WK04-00080
91.
Shaft for hyd. cylinder
WK04-00064
115.
Moving plate
WK04-00081
92.
Bolt M8x16
WK04-00013
116.
Bolt M8x16
WK04-00013
PARTS LIST….cont
7
CAUTION:
The warnings and cautions mentioned in this user manual can not cover all possible
conditions and situations that may occur. It must be understood by the operator that com-
mon sense and caution are factors which cannot be built into this product, but must be ap-
plied.
SAFETY INSTRUCTIONS….cont
and safest performance.
ALWAYS
wear approved eye and ear protection when operating the machine.
If any dust is produced, wear an approved face or dust mask.
WARNING!
round bar and tubing have a tendency to roll whilst being cut and can
cause the blade to slip,
DO NOT
cut such items without clamping or blocking the
material.
DO NOT
start the bandsaw until the material is secure and the blade has been low-
ered to just above the material.
NEVER
use damaged or deformed bandsaw blades.
ALWAYS
secure the material that is too be cut in the vice.
NEVER
use the bandsaw with the blade guard or pulley cover removed.
DO NOT
use whilst under the influence of drugs, alcohol or other intoxicating medi-
cation.
NEVER
start the bandsaw with the blade in contact with the workpiece.
ALWAYS
allow the bandsaw to reach full speed before commencing the cutting op-
eration.
NEVER
use this bandsaw for any application other than that specified by the manu-
facturer.
Never operate this bandsaw under conditions not approved by the manufacturer.
Before using or servicing your bandsaw, read and understand all instructions. Failure
to follow safety precautions or instructions can cause equipment damage and/or
serious personal injury.
WEAR THE CORRECT CLOTHING.
Do not wear loose clothing, neckties, rings, brace-
lets, or other jewellery, which may get caught in moving parts. Non-slip footwear is
recommended. Wear protective hair covering to contain long hair. Roll long sleeves
up above the elbow.
If the bandsaw is used in a place of work all rules and laws etc. relating to the use of
portable electrical appliances should be followed.
When using the saw, particularly during extended periods; ensure the opera-
tor as well as those in the area wear ear protection.
When using the saw always ensure the operator as well as those in the area
wear eye protection.
Some materials have the potential to be highly toxic; always wear a face
mask when operating the saw.