background image

Sinterit SANDBLASTER XL User Manual   |  5

ATTENTION!

After each use of the Sinterit SANDBLASTER XL, wash your hands.

 

D. POWER SUPPLY

WARNING!

• 

Before plugging in, make sure the power voltage and frequency are those 
shown on the machine safety plate. 

• 

Make sure the machine is properly grounded. In case you are using an 
extension, check if it is grounded and if the capacity is sufficient.

• 

During use, mind the power supply cables and avoid crushing or pulling these.

• 

Periodically check the mains power cable to ensure it is not damaged.

• 

In the event of the cable, plugs or couplings being replaced, make sure these 
are protected against water spray and check mechanical strength.

STOP!

• 

Never touch electric cables, switches, buttons, etc. with wet hands.

• 

In the event of the cable being damaged, the machine must not be used.

• 

Never pull the machine by means of the power cable. 

E. SAFETY DURING SANDBLASTING, REPAIR AND MAINTENANCE

ATTENTION!

• 

Check the quality of all hoses and pneumatic tubing before each use.  Check that all 
connections are secured.

• 

Check the machine previous to each use for damaged and/or defect parts. Pay special 
attention if all seals are still good and check all tubing for leakages.

• 

Check that all components of the Sinterit SANDBLASTER XL are properly sealed.

• 

Check the machine for defects previous to each use, in case of a defect, or when the machine 
does not function properly, first have it repaired by a specialized person/company.

• 

Failure to heed these instructions may cause damage to materials and/or injures!

ATTENTION!

• 

Do not direct the Air Blow Guns 

D

20

 at people or objects.

• 

Do not exceed the maximum operating pressure of the Sinterit SANDBLASTER XL.

 

F. SCRAPPING

IMPORTANT!

In case of scrapping, all the component parts of the sandblaster will have to be 
disposed of through adequate disposal channels in accordance with applicable 
legislation. Before scrapping, all plastic and rubber parts will have to be separated 
from the electrical material. Parts made of plastic, aluminium and steel only may 
be recycled if collected by special centres. 

Содержание SANDBLASTER XL





















Отзывы: