Singer 20E910 Скачать руководство пользователя страница 11

Страница: 11 / 64

Zigzag Sewing Machine

Instruction Manual and Parts List

3.3

Belt Cover

Installation

Figure 5

The machine belt cover

Install the machine belt cover so
that the hand wheel and v-belt
move freely without interference,
and then tighten the screw at this
position (see Figure 5).

The motor belt cover

Install the motor belt cover so that
motor pulley and v-belt will rotate
freely without interference.

Caution

Switch off the

machine.

Set sewing head

upright again

using both hands.

Danger of crush-

ing between

sewing head and

table top.

For your safety,

do not run the

machine without

the belt cover.

3.4

Operation

Panel

Installation

(for 20E-910

only)

Figure 6

Install the operation panel ’

’ to the

bracket ‘

’ by two screws ‘

’.

Then the operation panel with the
bracket is attached into the machine
by setscrew ‘

’.

Содержание 20E910

































































Результаты поиска

Содержание 20E910

Отзывы:

Похожие инструкции для 20E910

Бренды по названию

Популярные бренды

Singer 20E910, Инструкция и список запасных частей

Результаты поиска

Содержание 20E910

Отзывы:

Похожие инструкции для 20E910

Бренды по названию

Популярные бренды