Singer 20E910 Скачать руководство пользователя страница 33

Страница: 33 / 64

Zigzag Sewing Machine

Instruction Manual and Parts List

Troubleshooting

Whenever sewing difﬁculty is encountered, check and make adjustments as follows.

*** If you still have difﬁculty in sewing even after making adjustments,
contact your nearest Service Center.

Problem

Possible Causes

Possible Solutions

1. Is machine properly threaded

1. Correct needle threading

2. Are thread guides or tension disc area lint-free

2. Remove lint & ﬂuff in bobbin case & hook

3. Is needle-thread tension too tight

3. Adjust needle thread tension

4. Is needle bent or has a blunt point

4. Insert new needle

5. Is needle inserted correctly

5. Insert needle correctly

6. Is needle the correct size for thread & fabric

6. Select proper needle size & thread

7. Is poor quality thread

7. Change the thread

1. Is bobbin threading correct

1. Correct bobbin threading

2. Is thread tangled or caught

2. Untangle thread from bobbin case & hook

3. Is thread tension correct

3. Adjust needle & bobbin case thread tension

4. Does bobbin rotate smoothly

4. Check whether bobbin thread is wound correctly

1. Is needle inserted correctly

1. Insert needle correctly

2. Is needle bent or has blunt needle point

2. Insert new needle

3. Is size of needle & thread suitable for fabric

3. Select proper needle size & thread

4. Is threading correct

4. Correct needle threading

1. Is needle installed wrong

1. Install needle correctly

2. Is needle bent

2. Replace needle

3. Is needle the correct size for the fabric

3. Select proper needle & thread for fabric

4. Is needle clamping screw loose

4. Tighten needle set screw

5. Is the fabric pulled while sewing

5. Do not pull fabric while sewing

1. Is feed regulating dial properly adjusted

1. Lengthen stitch length by feed regulating dial

2. Is presser foot pressure adjusted properly

2. Adjust correct presser toot pressure

1. Is needle threading correct

1. Correct needle threading

2. Is needle point blunt

2. Replace needle

3. Is thread tension too tight

3. Adjust needle tension properly

1. Is there any lint or ﬂuff on feed dog

1. Remove lint & ﬂuff from feed dog

2. Is there any lint in rotating hook

2. Remove lint & ﬂuff from rotating hook

1. Are electrical plugs properly connected

1. Turn on power switch

2. Is power & light switch turned on

2. Connect plug to power source

Fabric fails to

feed

Fabric puckers

Rotating heavy

noise

Machine fails to

start

Needle thread

breaks

Bobbin thread

breaks

Skip stitches

Needle break

Содержание 20E910

































































Результаты поиска

Содержание 20E910

Отзывы:

Похожие инструкции для 20E910

Бренды по названию

Популярные бренды

Singer 20E910, Инструкция и список запасных частей

Результаты поиска

Содержание 20E910

Отзывы:

Похожие инструкции для 20E910

Бренды по названию

Популярные бренды