SImx LHT0088 Скачать руководство пользователя страница 5

SECTION THREE

INSTALLATION

Mark position of the fixing holes. (Fig C)
Drill the holes. Insert the wall plugs into the holes.

PASS THE CABLE THROUGH THE WALL BRACKET BEFORE SECURING WALL BRACKET
TO THE WALL. 

Pierce the grommet and pass the cable through the wall bracket.
Allow approximately 70mm of cable to pass through the grommet. (A template for this wire length
is provided on the rear cover of this manual).

Fit grommet into its location hole ensuring a good seal.
Fix the mounting plate to the wall. Take care not to overtighten the screws to prevent damage to
the mounting plate. If using a power screwdriver, use the lowest torque setting.

Unfasten the screw on the top of the floodlight.  Install the halogen bulb, making sure not to touch
the bulb with bare hands.  It is suggested that the bulb is handled using a dry cloth.  
Ensure the bulb is correctly fitted in the lampholder before use.
Re-attach the front cover, do not overtighten the fixing screw.

*** IMPORTANT ***

Switch off the electricity at the fuse box by removing the relevant fuse or switching off

the circuit breaker before proceeding with the installation.

CONNECTION

This unit is supplied with a hanging attachment (tether) to aid installation.
If it is not required, simply remove from the unit and discard.

Place the round end of the tether into the keyhole shape location hole on the wall bracket.
Ensure the tether is securely fixed into the slot before releasing the weight of the unit.

The unit can now be suspended below the wall bracket. (Fig D)

Connect the cable to the terminal block as follows (see connection diagram):

NEUTRAL (Blue) 

N

EARTH (Green/Yellow)
LIVE (Brown)

L

Ensure the connectors are secure.

Place terminal block onto its securing pillar on the wall bracket (Fig E)

Fit floodlight to wall bracket and secure by fixing screw (Fig F)

LHT0088&89 251012:lht008889.qxd  10/26/12  5:14 PM  Page 5

Содержание LHT0088













Отзывы: