manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

Software updates

Before initiating an update to the unit, be sure to back up any
potentially valuable user data. Refer to 

"Backing up your system data"

 on

page 224.

Installed software and software updates

The about dialog shows the software version currently installed on
this unit (

A

).

If the unit is connected to internet, the dialog also shows available
software updates (

B

).

Update the software when connected to internet

If the unit is connected to internet, the system will automatically
check for software updates for the unit and for connected devices.

Ú

Note: 

Some software update files might be larger than the

space available in the unit. If so, you will be prompted to insert a
storage device.

Maintenance

 | GO XSE/XSR Operator Manual

221

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

Makita EM2650LH Instruction Manual preview
EM2650LH
Бренд: Makita Страницы: 84
SALUDA MEDICAL Evoke Clinical Manual preview
Evoke
Бренд: SALUDA MEDICAL Страницы: 61
Panasonic SF2B Series Instruction Manual preview
SF2B Series
Бренд: Panasonic Страницы: 30
T-Rex BIG FOOT User Manual preview
BIG FOOT
Бренд: T-Rex Страницы: 13
H&S 5126 Operator'S Manual preview
5126
Бренд: H&S Страницы: 42
Parker HTG Series Service Procedure preview
HTG Series
Бренд: Parker Страницы: 64
Parker F11 series Service Spare Parts List preview
F11 series
Бренд: Parker Страницы: 40
Parker Matrx Digital MDM Cabinet Mount Installation Instructions preview
Matrx Digital MDM
Бренд: Parker Страницы: 20
Parkside PFMR 1600 A1 Operation And Safety Notes preview
PFMR 1600 A1
Бренд: Parkside Страницы: 95
L-Acoustics LA4X Technical Bulletin preview
LA4X
Бренд: L-Acoustics Страницы: 5
Harken 3294 Instructions preview
3294
Бренд: Harken Страницы: 4
BARRON Exitronix LEMD Series Installation Instructions Manual preview
Exitronix LEMD Series
Бренд: BARRON Страницы: 6
Wayflex SHAKE IT User Manual preview
SHAKE IT
Бренд: Wayflex Страницы: 11
T-SoX So-exercise TX7 Manual preview
So-exercise TX7
Бренд: T-SoX Страницы: 8
OMGA TR 2B INC INT NC Operation And Maintenance Manual preview
TR 2B INC INT NC
Бренд: OMGA Страницы: 76
ALL-FILL VF100e Installation & Maintenance Manual preview
VF100e
Бренд: ALL-FILL Страницы: 32
Blatchford ESK+ Manual Knee Lock Instructions For Use Manual preview
ESK+ Manual Knee Lock
Бренд: Blatchford Страницы: 172
HEINE OPTOTECHNIK iC2 Funduscope Manual preview
iC2 Funduscope
Бренд: HEINE OPTOTECHNIK Страницы: 52

Бренды по названию

Популярные бренды

Загрузить еще бренды