SimpliFire SF-ALL48-BK Скачать руководство пользователя

Страница: 14 / 21

SimpliFire • SF-ALL48-BK, SF-ALL60-BK • 2040-981 Rev. C • 3/18

Figure 4.14 Optional Power Cord Assembly (Only for Direct Wall Mount Installation)

E. Electrical Connection / Installation

Note: All wiring must be completed prior to finishing

the unit.

All electrical connections shall be performed by a

qualified electrician.

WARNING! Risk of Fire, Electrical Shock and Injury!

Electrical wiring must comply with local building codes

and other applicable regulations.

WARNING! Risk of Shock!

Label all wires prior to dis-

connection when servicing the appliance. Wiring errors

can cause improper and dangerous operation. Verify

proper operation after servicing.

This appliance has been designed to be hard-wired for

120V. A supplied plug-in kit is also available for installa-

tions mounted directly on the face of the wall.

A 15 AMP, 120V/60Hz circuit is required. Additional ap-

pliances on the same circuit as this appliance may ex-

ceed the current rating of that circuit. A dedicated circuit

is not required, but is preferred to prevent circuit breaker

trips or fuse failure.

Hard-Wired Installation

Note

: The appliance must be electrically connected and

grounded in accordance with local codes.
1. Remove terminal block cover plate located on the

right end of the appliance.
2. Install a wire strain relief bushing into the cover

plate.

3. Terminate type NM-B wire to the terminal block,

ensure connections are secure, and tighten the

strain relief.
4. Replace terminal block cover plate and retaining

screws.

WARNING!

Risk of Fire, Electrical Shock and Injury!

Ensure the power cord is not installed so that it is pinched

or against a sharp edge and ensure that the power cord is

stored or secure to avoid tripping and snagging.

Power Cord Installation

The appliance power cord has a three pin NEMA-5-15P

plug. The power cord should not be used unless a

grounded receptacle is available.
1. Remove the terminal block cover plate located on

the right end of the appliance.
2. Disconnect the terminal block from the three wires

inside the appliance. Discard the terminal block

cover plate.
3. Connect the three appliance wires to the terminal

block supplied with the power cord kit. See Figure

4.14.
4. Replace cord kit terminal block cover plate

and retaining screws. Plug cord into nearest outlet.

See Figure 3.3.

RED

YELLOW / GREEN

BLUE

Wire Diagram

Содержание SF-ALL48-BK






















Результаты поиска

Содержание SF-ALL48-BK

Отзывы:

Похожие инструкции для SF-ALL48-BK

Бренды по названию

Популярные бренды

SimpliFire SF-ALL48-BK, Руководство пользователя

Результаты поиска

Содержание SF-ALL48-BK

Отзывы:

Похожие инструкции для SF-ALL48-BK

Бренды по названию

Популярные бренды