background image

SimpliFire  • SF-ALL40-BK, SF-ALL48-BK, SF-ALL60-BK, SF-ALL84-BK  •  2040-981 Rev. M  •  7/21

  

20

A.  Maintenance 

WARNING! Risk of Shock! 

Always remove power before 

moving or servicing.  Do not immerse appliance in water.

•  Before cleaning or servicing, always turn off appli-

ance and remove power, by either unplugging from 

the wall outlet or shutting off circuit breaker. 

•  Light accumulated dust may be removed from the ap-

pliance exterior with a soft cloth or vacuum cleaner. 

•  Wipe the exterior surfaces of the appliance occasion-

ally with a slightly damp micro fiber cloth using a so-

lution of mild detergent and water.  Dry thoroughly 

before operating the appliance. 

CAUTION! 

Do not allow water to run into the interior of 

the appliance as this could create a fire or electric shock. 

Always remove power before moving or servicing.  

•  The fan motor is factory lubricated for life and will not 

require further lubrication.

•  Store appliance in a clean dry place when not in use.

WARNING! Risk of Fire! 

To reduce risk of fire, do not 

store or use gasoline or any other flammable vapors or 

liquids in the vicinity of the appliance. 

WARNING! Risk of Electrical Shock! 

Any other servic-

ing needed must be performed by an authorized service 

representative.  Do not attempt to service the unit your-

self.

B.  Cleaning

Cleaning Glass

D

ust  particles  can  be  removed  by  buffing  lightly  with  a 

clean dry cloth.  Fingerprints and other marks can be 

cleaned with a cloth dampened with a quality household 

glass cleaner.  The glass should be completely dried with 

a lint free cloth or paper towel.  Do not use abrasive clean-

ers on glass surface.  Do not spray liquids directly onto 

any surface.

Metal Surface

D

ust  particles  can  be  removed  by  buffing  lightly  with  a 

clean dry cloth.  A damp cloth can be used to clean paint-

ed surfaces.  Do not use abrasive cleaners.  Do not spray 

liquids directly on to any surface.

MAINTENANCE

 

 

C.  Servicing

Except for cleaning, an authorized service representative 

should perform any other service.

Содержание SF-ALL40-BK




























Отзывы: