manualshive.com logo in svg

Simplicity Citation 5900522, Руководство по настройке и регулировке дилера

Поделиться
Скачать
Simplicity Citation 5900522 Скачать руководство пользователя страница 2

Citation - 52” & 61” Mower Decks

www.simplicitymfg.com

2

Quick Setup List  

Page

Setup Procedure

Steps to Perform

3

Uncrating

❏
❏
❏
❏

Remove Crate & Banding.
Loosen Hydraulic Release Valves.
Release Parking Brake and Roll Tractor forward off skid.
Tighten Hydraulic Release Valves.

3

Connect Battery Cables

❏

Connect Battery Cables.

4

Tractor Assembly

❏
❏
❏

Assemble the Ground Speed Control Levers.
Assemble the Seat.
Connect the Seat Switch Harness.

5

Roll Bar Assembly

❏
❏
❏

Assemble the Retainer Pins.
Assemble the Top Loop.
Install the Roll Bar.

7

Check Fluid Levels

❏
❏
❏

Check Engine Oil Level.
Check Hydraulic Oil Level.
Check Tire Pressure

8

Check Mower Assembly

❏
❏
❏

Check Blade Bolt Torque
Check and Level Mower Deck
Check Deck Drive Belt

14

Lubrication & Fuel Preparation

❏
❏
❏

Lubricate all grease and oil points.
Add fuel.
Start the Engine.

16

SAFETY CHECK

❏
❏
❏

Check for LOOSE HARDWARE.
Check all OPERATOR CONTROLS.
Perform SAFETY INTERLOCK SYSTEM CHECK.

Register Product

❏

To register the product: log onto www.thepowerportal.com, 
select the appropriate brand, click “My Resources,” select the 
“Product Registration and Rebate” icon and then the “New 
Product Registration / Rebate” tab.  Fill out and submit the 
online product registration form.

Setup Procedures

Not 

for  

Reproduction

Содержание Citation 5900522





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды