Simplicity 653 Скачать руководство пользователя страница 19

Страница: 19 / 28

FIGURE 37

FIGURE 38

7. Check the Transmission Oil Level (Variable Speed

Transmission):

Remove the plug at the right rear of the

transmission. See figure 39. The oil should be level with
the bottom of this hole. If necessary add SAE 90

mission oil. Replace the plug and tighten securely. It is not

FIGURE 39

normally necessary. but if you wish

drain oil from the

transmission; the drain plug is located at the lower right

side of the transmission.

(Hydrostatic Transmission):

Check the oil level of the hy-

drostatic unit with the engine stopped

the plug in the

reservoir. (See figure

Turn the plug counterclockwise

to remove. The oil should be

with the bottom of the

threads. If it is not. remove the

from

the top of the reservoir and add Dexron automotive

mission fluid which is available locally from

major

oil companies. Replace the

and

plug and tighten

The hydraulic oil

t h e

bottom of the reservoir has

be changed only when dirt

gets into the hydraulic oil in the reservoir

the hydrosta-

tic transmission is removed for repair.

it should be nec-

essary to change the filter,

the nut and

from

the top of the reservoir. Disconnect one of the hoses at the

bottom of the reservoir to drain the oil. Raise the end of
the hose and tie it up so oil will not run out of the

mission. Remove the filter and replace with a new one. Re-
place the hose and add Dexron Automatic Transmission

Fluid to the reservoir up to the level of the inspection

plug. Replace the

and nut on the reservoir.

FIGURE 40

Remove the snap out rubber plug from the fan and oil

cooler housing and clean fan and

air

water

under pressure. Replace the plug by pressing it into the

hole.

Check the oil level in the

housing at the elbow located

at the rear of the housing. Remove the pipe plug from the

elbow. Oil should be level with the top of the elbow. If

necessary, add SAE 90 wt. transmission oil. Replace the

plug and tighten securely ( See figure 40).

Check the

Battery

Water Level

to insure it is maintained

at the battery ring

approximately

inch above the

plates. See figure 41. If water is needed, add distilled water

Содержание 653





























Результаты поиска

Содержание 653

Отзывы:

Похожие инструкции для 653

Бренды по названию

Популярные бренды

Simplicity 653, Руководство оператора

Результаты поиска

Содержание 653

Отзывы:

Похожие инструкции для 653

Бренды по названию

Популярные бренды