Simplicity 5901597 Скачать руководство пользователя страница 13

Страница: 13 / 48

Not for

Reproduction

Zero-Turn Rider Controls

Callout

Control Name

Deck Lift Pedal

Cutting Height Adjustment Pin

Deck Lift Lock Lever

Parking Brake

Seat Adjustment Lever

Roll Bar

Ground Speed Control Levers

Fuel Selector Valve

Fuel Tank Cap (One per fuel tank)

Fuel Level Gauge (One per fuel tank)

Retractable Seat Belt

Removable Floor Plate

Transmission Oil Fill / Tanks (One per transmission)

Transmission Release Levers (One per transmission)

Seat Latch

Deck Lift Pedal, Cutting Height Adjustment Pin & Deck

Lift Lock Lever:

The deck lift pedal (A, Figure 6), the cutting

height adjustment pin (B), and the deck lift lock lever (C) are

used together to control the cutting height of the mower deck.

See

Cutting Height Adjustment

for instructions on using these

controls.

Cutting Height Adjustment Pin

Deck Lift Lock Lever

Parking Brake:

Pull the parking brake lever up and

back to engage the parking brake. Move the lever fully

forward and down to disengage the parking brake.

Note:

To start the unit the parking brake must be engaged.

Engaging the parking brake locks the ground speed control

levers in the NEUTRAL position. The parking brake must be

disengaged before moving the ground speed control levers

out of the NEUTRAL position.

Disengage

Releases the parking brake.

Engage

Locks the parking brake.

Seat Adjustment Lever:

The seat can be adjusted forward

and back. Move the lever towards the left, position the seat as

desired, and release the lever to lock the seat in position.

Suspension Seat:

Some models are equipped with a

suspension seat. This seat has several additional options.

See Figure 7 and the chart below for the location of the seats

features and brief description of their function.

Содержание 5901597

















































Результаты поиска

Содержание 5901597

Отзывы:

Похожие инструкции для 5901597

Бренды по названию

Популярные бренды

Simplicity 5901597, Руководство оператора

Результаты поиска

Содержание 5901597

Отзывы:

Похожие инструкции для 5901597

Бренды по названию

Популярные бренды