Simplicity 5901597 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 48

background image

Not for

Reproduction

26

simplicitymfg.com

27

7. Remove the cap from the drain spout of the oil drain

valve.

8. To operate the oil drain valve, turn

counter-clockwise

to

open and drain the engine oil into a suitable container.

9. After the engine oil has drained, turn the oil drain valve

clockwise

to close and re-install the cap on the oil drain

valve.

10. Pour oil into the engine oil fill (F, Figure 26). The remote

oil tank is designed to hold 5 qt (4,73 L) of engine oil.

11. Install the engine oil dipstick (A, Figure 28) into the tank

by pressing down firmly with your hand. The engine oil

dipstick has a detent (B) and it must snap into place on

the lip (C) of the tank housing so that the dipstick is fully

installed into the tank. This action requires moderate

force.

28

12. Remove the engine oil dipstick and check the oil level.

Maximum oil level is the "FULL" line (G, Figure 26) on the

dipstick. If the oil level is at or below the "ADD 1 QT." line

(H), add more oil.

13. Re-install the dipstick.
14. Install a new engine oil filter by lowering it into the engine

oil fill and then turning

clockwise

a 1/4 turn (I).

15. Close the oil fill cover.
16. Start and run the engine. As the engine warms up, check

for oil leaks.

17. Stop the engine and check oil level. Add more if

necessary.

18. If desired, a new self-locking tie can be installed to keep

the oil fill cover securely closed.

Changing the Engine Oil and Filter (All

Other Models)

This series of mower also features a Briggs & Stratton

Vanguard Series (A, Figure 29) engine.

«
...
24
25
26
27
28
...
»

Содержание 5901597

















































Отзывы:

Нет отзывов

Похожие инструкции для 5901597

Бренд: Yard Machines Страницы: 20

Бренд: MTD Страницы: 6

Бренд: Qualcast Страницы: 24

Бренд: Jacobsen Страницы: 98

Бренд: Poulan Pro Страницы: 8

Бренд: Rapid Страницы: 9

Бренд: Gardenline Страницы: 24

Бренд: AS MOTOR Страницы: 36

Super Recycler 20062

Бренд: Toro Страницы: 20

Бренд: MTD Страницы: 16

Бренд: Yard-Man Страницы: 18

Бренд: Gardif Страницы: 22

PRO-12 41721209

Бренд: Peco Страницы: 20

Бренд: Yard-Man Страницы: 36

Бренд: Snapper Страницы: 72

Бренд: Husqvarna Страницы: 56

Бренд: Husqvarna Страницы: 65

Бренд: Husqvarna Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды