Simplicity 1695665 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 36

background image

Adjusting Belt Drive

Figure 28

BELT GUIDE ADJUSTMENT

1. Remove spark plug wire.

2. Have someone engage the auger drive. This will engage auger idler

pulley (A

A, Figure 28).

3. Measure the distance between the belt guide (B

B) and belt (C

C). The

distance should be about 1/8 inch (3 mm).

4. If adjustment is necessary, loosen belt guide mounting bolt. Move

belt guide to the correct position. Tighten mounting bolt.

5. Install belt cover.

6. Connect spark plug wire.

1/8” (3mm)

Screw

A

B

C

25

Adjusting Auger Drive Belt

Figure 26

1/2”

(12.5mm)

Deflection

8 3

Check Tension on Auger Drive Belt

Figure 27

B

B

A

MAINTENANCE

A

B

BELT ADJUSTMENT
Traction Drive Belt

The traction drive belt has constant spring pressure and does not require
an adjustment. If the traction drive belt is slipping, replace the belt. See
authorized dealer.

Auger Drive Belt

If your snowthrower will not discharge snow, check the control cable
adjustment. If it is correct, then check the condition of the auger drive belt. If it
is damaged or loose, replace it (see authorized dealer).

Auger Drive Belt Adjustment:

1. Disconnect spark plug wire.

2. Remove screw (A

A, Figure 26) from belt cover (B

B). Remove belt cover.

3. Loosen nut on idler pulley (A

A, Figure 27) and move idler pulley

towards belt about 1/8 inch (3 mm).

WARNING: Do not over-tighten, as this may lift the
lever and cause the auger drive to be engaged without
depressing the auger control lever.

4. Tighten nut.

5. With the aid of an assistant, engage the auger drive clutch. Check

tension on belt which is opposite idler pulley (A

A, Figure 27). Belt

should deflect about 1/2 inch (12.5 mm) with moderate pressure.
You may have to move idler pulley more than once to obtain the
correct tension.

6. Reinstall belt cover (B

B, Figure 26). Tighten screw (A

A).

7. Attach the spark plug wire.

NOTE: Whenever belts are adjusted or replaced, the cables
will need to be adjusted (see “Check and Adjust the Cables”
section).

Check Auger Drive Belt:

1. Release the auger control lever.

The auger must stop within 5

seconds.

2. If auger does not operate properly, stop engine and repeat “Auger

Drive Belt Adjustment.”

Not

for

Reproduction

«
...
23
24
25
26
27
...
»

Содержание 1695665





































Отзывы:

Нет отзывов

Похожие инструкции для 1695665

Бренд: Weed Eater Страницы: 13

Бренд: E-FLOR Страницы: 124

Бренд: STOLZENBERG Страницы: 9

Бренд: GreenWorks Страницы: 116

Бренд: Waterco Страницы: 12

Бренд: Simplicity Страницы: 20

Бренд: Simplicity Страницы: 24

POWER X CHANGE PXCBLK-418

Бренд: Ozito Страницы: 6

Бренд: Deltafox Страницы: 116

snow commander 38603

Бренд: Toro Страницы: 12

Бренд: Scheppach Страницы: 88

Бренд: Verdemax Страницы: 20

Бренд: Garland Страницы: 112

Бренд: ST. SpA Страницы: 31

Бренд: Troy-Bilt Страницы: 52

Бренд: AgriMetal Страницы: 6

Бренд: FIORENTINI Страницы: 37

Бренд: Kubota Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды