background image

40” SNOWTHROWER

SAFETYRULES

A

Read these safety rules and follow them closely. Failure to obey these roles could result in loss of control

of vehicle, severe personal injury to yourself or bystanders, or damage to property or equipment. The 

 

in the text signifies important cautions or warnings which must be followed.

A

ALL WARNING, CAUTION, and instructional
messages on this attachment and on your

tractor should be carefully read and obeyed. Per-
sonal bodily injury can result when these instruc-
tions are not followed.

A

WARNING

If the auger stalls or the chute plugs, DISEN-

GAGE THE ELECTRIC CLUTCH, STOP THE

ENGINE, REMOVE THE KEY AND SET THE
PARKING BRAKE. WAIT FOR MOVING
PARTS TO STOP. Remove the foreign object

or clear the spout with piece of wood before
restarting the engine. Never place hands into
auger housing or spout to clear jammed
object. Auger may rotate when object is

removed.

Read this manual and the tractor Operator’s
Manual carefully. Be thoroughly familiar with the

controls and the proper use of the equipment.

l

Never allow children to operate the machine. Do
not allow adults to operate it without proper
instruction.

l

Do not carry passengers.

l

Use only attachments or accessories designed

for your machine. See your dealer for a complete

list of recommended attachments or accessories.

l

Keep the area of operation clear of all persons,

particularly small children and pets.

l

Never discharge toward bystanders.

Make sure:

a. all nuts and screws are tight and snowthrower

is in good operating condition.

b. all safety devices and shields 

 place and

in good working condition.

c. all adjustments 

are 

correct before using unit.

Preparation

l

Never attempt to make any adjustments while
engine is running.

l

Thoroughly inspect the area where the

snowthrower is to be used and remove all door
mats, sleds, boards, wires and other foreign
objects.

l

Adjust skid shoe height to clear gravel or crushed

rock surface.

Operation

l

Always clear snow up and down the face of
slopes, and never across the face. Exercise
extreme caution when changing direction on
slopes. Do not attempt to clear steep slopes.

l

Exercise extreme caution when operating on or

crossing gravel drives, walks, or roads. Stay alert
for hidden hazards or traffic.

l

After striking an object or if unit starts to vibrate
abnormally, stop the engine, disengage electric
clutch, and remove the key. Check for the cause
and any damage before restarting. Before inspect-

ing, make sure all moving parts have stopped.

l

Take all possible precautions before leaving oper-
ator’s position. Disengage the electric clutch,

lower the attachment, set the parking brake, stop

the engine and remove the key.

l

Never operate snowthrower near glass enclo-

sures, automobiles, window wells, dropoffs, etc.

without proper adjustment of snow discharge
angle.

l

Do not operate machine at high transport speeds

on slippery surfaces. Use care when backing.

Disengage power to snowthrower when transport-
ing or not in use.

l

Never operate the snowthrower without good visi-
bility or light. always be sure your feet are properly
placed on the foot rests and keep a firm hold on

the steering wheel.

Содержание 1692356



























Отзывы: