Simplicity 1691521 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 36

background image

10

Figure 9. Discharge Chute & Controls
A. Discharge Chute

F. 1" Capscrew & Locknut

B. Rod Guide Liner

G. Clip

C. Rod Guide

H. Dis. Chute Control Rod

D. Pivot Bearing

I. Notch

E. Support Arm

J. 3-1/2" Capscrew & Locknut

K. Spacer

CAUTION

Do not let the pivot bearing (D, Figure 9) support
the weight of the control rod or the bearing could
be damaged.

SNOWTHROWER ASSEMBLY

Assemble Support Arm and Control Rod

1. See Figure 9. Attach the support arm (E) to the

frame with the 1" capscrews and locknuts (F) sup-
plied.

2. See Figure 9. Place the the thin, plastic liner (B)

inside the rod guide (C). Place the rod guide (C) over
the discharge chute control rod (H) and loosely
attach the guide to the support arm (E) in either of
the top two mounting holes. Use the capscrew and
locknut (J) and spacer (K) provided.

3. See Figure 9. Install the discharge chute control rod

(H) through the plastic pivot bearing (D) on the auger
housing. Place a cotter pin into the lowest rod hole
on the inside of the housing, and spread the cotter
pin fully around the rod.

4. Pull the rod back so the cotter pin is resting against

the bearing (D), then insert a second cotter pin
through the rod, just above the bearing. Spread the
cotter pin fully around the rod.

5. Tighten the locknut and capscrew (J) securing the

control rod guide. Do not overtighten. This nut and
capscrew are used to set the control rod rotation
resistance.

Assemble Discharge Chute & Control Cable

1. See Figure 9. Install the discharge chute (A) so the

clip (G) on the housing is positioned in the notch (I).
Lubricate the discharge chute so it turns freely.

2. See Figure 10. With the discharge chute facing

slightly left, wind the cable around the control rod
spool. Wind it three turns on the rear part of the
spool so that the cable leaves the spool on the lower
edge as shown. Wind two turns on the front part of
the spool so the cable leaves the spool on the upper
edge as shown.

3. See Figure 10. Place the looped end of the cable

over the stud on the discharge chute. Place the small
flat washer (E) provided on the stud. Pull the other
end of the cable around the stud using locking pliers.
While holding the cable tight, install the cup washer
(B) (cup facing inward), lockwasher (C) and nut (D).
Tighten the nut and tape the cable end to the taut
section of the cable.

Figure 10. Control Cable
A. Cotter Pin

C. Lockwasher

B. Cup Washer`

D. Nut
E. Flat Washer

K

Regent Snowthrower Assembly

«
...
12
13
14
15
16
...
»

Содержание 1691521





































Отзывы:

Нет отзывов

Похожие инструкции для 1691521

Бренд: Columbus Страницы: 8

Бренд: Black Max Страницы: 42

Бренд: Yard-Man Страницы: 28

Бренд: Ariens Страницы: 30

Бренд: GreenWorks Pro Страницы: 22

Бренд: Zenoah Страницы: 20

Бренд: Zenoah Страницы: 14

Бренд: Tomahawk Страницы: 46

Бренд: Ribimex Страницы: 28

Бренд: Giant-Vac Страницы: 14

Бренд: Viking Range Страницы: 36

Бренд: Meec tools Страницы: 136

Бренд: Homelite Страницы: 2

Бренд: Tennant Страницы: 68

Power Clear 721

Бренд: Toro Страницы: 24

Бренд: Toro Страницы: 16

Бренд: Nortec Страницы: 30

Бренд: Zeppelin Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды