Simplicity 1691521 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 36

background image

Assemble the Deflector

1. See Figure 28. Attach the deflector (C) to the dis-

charge chute with two screws (H), washers (G), spac-
ers (F), washers (A), lockwashers (E) and nuts (D).

2. Position the bolt (I) and washer (A), then thread the

knob (B) onto the bolt (I)

Assemble the Hitch Brackets and Spacers

1. Mount the hitch brackets and spacer to the inside of

the snowthrower capscrews and flange locknuts as
shown in Figures 29 - 31.

17

Broadmoor Snowthrower Assembly

Figure 28. Discharge Chute
A. Washer, 5/16

F. Spacer

B. Knob

G. Washer, 5/16

C. Deflector

H. Screw, 5/16

D. Nut, 5/16

I. Carriage Bolt, 5/16

E. Lockwasher, 5/16

Figure 29. Installing the Hitch Brackets and Spacers
A. Hitch Brackets

E. Capscrew, 1-1/4"

B. Capscrew, 1"

F. Lockwasher

C. Locknut, Flange

G. Nut

D. Spacers

Figure 30 Hole Pattern - Left Side

Figure 31. Hole Pattern - Right Side.

NOTE: Support Arm Removed For Clarity

Hitch Bracket
(Mounted On
Inside)

Hitch Bracket
(Mounted On
Inside)

Spacer
(Mounted On
Inside)

Spacer
(Mounted On
Inside)

«
...
19
20
21
22
23
...
»

Содержание 1691521





































Отзывы:

Нет отзывов

Похожие инструкции для 1691521

Бренд: Ryobi Страницы: 16

Бренд: Tanaka Страницы: 32

Бренд: Flex Страницы: 44

Бренд: Poulan Pro Страницы: 32

Бренд: Cub Cadet Страницы: 12

Бренд: Bosch Страницы: 252

Бренд: Bosch Страницы: 227

Бренд: Bosch Страницы: 150

Бренд: Bosch Страницы: 22

Бренд: Bosch Страницы: 19

Бренд: Bosch Страницы: 16

Бренд: Troy-Bilt Страницы: 28

Polar Blast 10530

Бренд: Troy-Bilt Страницы: 32

Бренд: Snapper Страницы: 6

Бренд: Static Clean Страницы: 4

Бренд: Acson Страницы: 56

Бренд: Worx Страницы: 28

Бренд: Kress Elektrowerkzeuge Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды