Simpact Freeway 2000 Скачать руководство пользователя страница 21

Страница: 21 / 86

DC 900-1331F

Freeway 2000 Certifications

The Freeway 2000 meets or exceeds the following standards:

Safety

UL 1950, CSA-C22.2 No. 950, and EN60950

Emissions

FCC US 47 CFR Part 15, Subpart B, and EN55022 (both to Class A)

Immunity

EN 50082-1 (1992)

The Freeway 2000 has been tested and found to comply with the limits for a Class A dig-

ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in

a commercial environment. The Freeway 2000 generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction man-

ual, may cause harmful interference to radio communications. Operation of this equip-

ment in a residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

Содержание Freeway 2000























































































Результаты поиска

Содержание Freeway 2000

Отзывы:

Похожие инструкции для Freeway 2000

Бренды по названию

Популярные бренды

Simpact Freeway 2000, Руководство по установке оборудования

Результаты поиска

Содержание Freeway 2000

Отзывы:

Похожие инструкции для Freeway 2000

Бренды по названию

Популярные бренды