Simex SWE-73-T, Руководство пользователя

Страница: 21 / 26

User manual for - INDICATOR SWE-73-T
8.1. LIST OF REGISTERS
Register Write Range Register description
01h No -999 ÷ 9999 Measurement value (no decimal point)
02h No 0h, A0h, 60h
The status of the current measurement;
0h
- data valid;
A0h
- top
border of the measurement range is exceeded; 60h - bottom border
of the measurement range is exceeded;
03h No 1 “ Pnt ” parameter (decimal point position), constant value 1 - “ 0.0 ”
06h No -999 ÷ 9999 Peak (drop) value (no decimal point)
10h Yes 0 ÷ 2
“
tyPE
” parameter in “
InPt
” menu (input type).
0
- Pt-100;
1
- Pt-500;
2
- Pt-1000
12h Yes 0 ÷ 5 “ FiLt ” parameter in “ InPt ” menu (measurement filtering rate)
18h Yes -99 ÷ 99
“ toFS ” parameter in “ InPt ” menu (shift of measurement scale ),
expressed by 0,1°C
20h 2 Yes 0 ÷ 199 Device address
21h No 20B2h Device identification code (ID)
22h 3 Yes 0 ÷ 7
“bAud” parameter in “rS” menu (baud rate);
0 - 1200 baud; 1 - 2400 baud; 2 - 4800 baud; 3 - 9600 baud;
4 - 19200 baud; 5 - 38400 baud; 6 - 57600 baud; 7 - 115200 baud
23h 4 Yes 0 ÷ 1
“mbAc” parameter in “rS” menu (permission to write registers via
RS-485 interface); 0 - write denied ; 1 - write allowed
25h Yes 0 ÷ 5
“rESP”
parameter in
“rS”
menu (additional response delay);
0
- no additional delay;
1
- ”
10c
” option;
2
- ”
20c
” option;
3
- ”
50c
” option;
4
- ”
100c
” option;
5
- ”
200c
” option;
2Dh Yes 1 ÷ 8
“ bri ” parameter (display brightness);
1 - the lowest brightness; 8 - the highest brightness
2Fh Yes 0 ÷ 1
“ Edit ” parameter (numerical parameters edit mode);
0 - „ dig ” mode; 1 - „ SLid ” mode
50h Yes 0 ÷ 1
“ modE ” parameter in “ HOLd ” menu (type of detected changes):
0 - peaks; 1 - drops
51h Yes 0 ÷ 9999
“ PEA ” parameter in “ HOLd ” menu (minimum detectable change, no
decimal point included)
52h Yes 0 ÷ 199
“ timE ” parameter in “ HOLd ” menu, maximum peaks' (or drops')
display time expressed in seconds
53h Yes 0 ÷ 1
“ HdiS ” parameter in “ HOLd ” menu:
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
2 - after writing to register no 20h the device responds with an “old” address in the message.
3 - after writing to register no 22h the device responds with the new baud rate.
4 - the value of the “mbAc” parameter is also connected to write to this register, so it is possible to block a writes, but
impossible to unblock writes via RS-485 interface, The unblocking of the writes is possible from menu level only.
21