Sime 8112265 Скачать руководство пользователя страница 27

Страница: 27 / 56

8.12.5

Brava Slim HE 20 R e

40 R e

The boilers

Brava Slim HE 20 R e

and

Brava Slim HE 40 R e

are

supplied already complete with coaxial ducts for smoke outlet

and combustion air inlet.

Fig. 26

KEY:

90° coaxial bend

Coaxial duct (supplied, but not fitted)

Air inlet

Smoke outlet

Outlet terminal (supplied, but not fitted)

Take-off point for smoke analysis

Ø 60/100

302 ( 20 R e)

247 ( 40 R e)

110

176

450

Fig. 27

8.13

Electrical connections

The power cable must be connected to a 230V (±10%) ~ 50 Hz

network, observing L-N polarity and the earth connection. The

network must have an omnipolar switch with category III over-

voltage, in compliance with the installation rules.

If this cable needs to be replaced, an original spare must be re-

quested from

Sime

Therefore only the connections of the original components as

shown in the table are needed. These are to be ordered sepa-

rately from the boiler.

DESCRIPTION

CODE

External sensor kit (ß=3435, NTC 10KOhm at 25°C)

8094101

Remote control HOME (open therm)

8092280

Remote control HOME PLUS (open therm)

8092281

CAUTION

The maintenance interventions described must ONLY

be carried out the professionally qualified personnel.

WARNING

Before carrying out any interventions described:
– set the main system switch to "OFF"
– close the gas valve
– make sure that no hot parts inside the appliance are

touched.

OFF

Fig. 28

To facilitate introduction of the connection wires of the optional

components into the boiler:

– disassemble the smoke outlet duct of the

Brava Slim HE 20 R e

and

Brava Slim HE 40 R e

, if fitted

– remove the screws (1), pull the front panel (2) forwards and

release it from the top by lifting it

Fig. 29

Содержание 8112265

























































Результаты поиска

Содержание 8112265

Отзывы:

Похожие инструкции для 8112265

Бренды по названию

Популярные бренды

Sime 8112265, Инструкция по эксплуатации, установке и обслуживанию

Результаты поиска

Содержание 8112265

Отзывы:

Похожие инструкции для 8112265

Бренды по названию

Популярные бренды