Sime 8112265 Скачать руководство пользователя страница 19

Страница: 19 / 56

7.10

Control panel

Fig. 14

FUNCTIONAL BUTTONS

If pressed once or more than once for at least 1 second

during normal operation, this button allows the user to

change the boiler operating mode in a cyclical sequence

(Stand-by – Summer – Winter). If the boiler is experienc-

ing a fault which can be reset, it allows boiler operation

to be unblocked. (Note: the "SUMMER" mode is not ap-

plicable to this boiler).

(

In "parameter setting", the user can scroll through the

parameter index (decreasing) by pressing this button.

During normal operation, pressing this button displays

the flow temperature set point which can be between 20

and 80°C. In "parameter setting", the user can scroll

through the parameter index (increasing) by pressing

this button.

During normal operation, pressing this button allows the

user to reduce the flow temperature set point. In "pa-

rameter setting/display", the user can modify the pa-

rameter setting or value (decreasing) by pressing this

button.

During normal operation, pressing this button allows

the user to increase the flow temperature set point. In

"parameter setting/display", the user can modify the

parameter setting or value (increasing) by pressing this

button.

Programming connector cover plug.

NOTE:

pressing any one of these buttons for more than 30 sec-

onds generates a fault on the display without preventing boiler

operation. The warning disappears when normal conditions are

restored.

DISPLAY

“SUMMER”

. The symbol for "Summer" mode is dis-

played. If the symbols

and

are flashing, this indi-

cates that the chimney sweep function is active.

“WINTER”

. This symbol appears when the boiler is oper-

ating in "Winter" mode. If no operating modes have been

enabled both symbols

and

will be off.

“RESET REQUIRED”

. The message indicates that after

having repaired the fault, normal boiler operation can be

restored by pressing the button

“HEATING”

. This symbol lights up during heating oper-

ation or during the "chimney sweep function It flashes

during the selection of the heating set point.

“BLOCK” DUE TO NO FLAME

“FLAME PRESENCE"

“POWER LEVEL"

. This indicates the power level at which

the boiler is operating.

“PARAMETER"

. This indicates that the user may be in

parameter setting/display, or "info" or "counter", or in

"activated alarms" (history).

“ALARM"

. This indicates that a fault has occurred. The

number specifies the cause which generated the alarm.

“CHIMNEY SWEEP"

. This indicates that the "chimney

sweep function" has been activated.

“HEATING SYSTEM PRESSURE"

. Display of heating system

pressure.

"ECO", ALTERNATIVE ENERGY SOURCES

. Where active, it

indicates that there is a solar system available.

"MAINTENANCE REQUEST"

. If active, it shows it is time to

perform maintenance on the boiler.

CAUTION

– Access to the control panel of models

Brava Slim HE

20 R e

and

Brava Slim HE 40 R e

is possible after loos-

ening screw (1) and removing panel (2).

– On completion of the operations, refit the panel on

the control panel and secure fully.

Fig. 15

Содержание 8112265

























































Результаты поиска

Содержание 8112265

Отзывы:

Похожие инструкции для 8112265

Бренды по названию

Популярные бренды

Sime 8112265, Инструкция по эксплуатации, установке и обслуживанию

Результаты поиска

Содержание 8112265

Отзывы:

Похожие инструкции для 8112265

Бренды по названию

Популярные бренды