Silverline 980960, Руководство пользователя

Страница: 13 / 84

EN
Original Instructions
silverlinetools.com
13
5. Remove the tool from the work surface before turning OFF
6. Allow the tool to stop rotating before putting it down
Cutting
Note:
This machine is not designed for wet cutting.
WARNING:
Always ensure the correct Cutting Guard (12) is installed
when using cutting discs or superabrasive wheels.
WARNING:
Only use discs specifically manufactured for cutting
operations. Stone and metal cutting discs are not interchangeable. Use the
correct disc for the application.
WARNING: Never use cutting discs for grinding operations. The disc
might shatter and produce projectiles that could injure the operator and/or
bystanders.
1. Position yourself so that the exposed underside of the
cutting wheel is facing away from you
2. Allow the tool to reach full speed before touching the tool
to the work surface
3. Apply light pressure to the work surface
Note : Excessive pressure does not result in more effective
or faster cutting, but will cause premature wear of the
cutting disc and increase wear and tear on the tool
4. Once a notch is established, keep the angle of the disc
constant
5. Allow the tool to stop rotating before putting it down
WARNING:
If the wheel is binding or when interrupting a cut for any
reason, switch off the tool and hold the tool motionless until the wheel
comes to a complete stop. Then remove the tool.
WARNING:
Do not apply any sideways force to cutting discs, as this
might lead to the disc becoming jammed in the cut and shattering.
IMPORTANT:
The cutting disc will wear during use, and the disc diameter
will gradually reduce in size. The smaller the disc becomes, the more strain
will be placed on the motor. Avoid damage to the tool by only using cutting
discs that fall within approximately 25% of the original size.
Using a cup brush or wire wheel
• Always check the no-load speed of the grinder does not
exceed the maximum speed of the cup brush or wire wheel
• Ensure no part of the cup brush or wire wheel can come
into contact with the tool housing
• Run the grinder, with cup brush or wire wheel attached, for
at least 30 seconds before use to check that the cup brush
or wire wheel is secure and properly balanced
IMPORTANT:
When using a wire cup brush or wire wheel, avoid applying
excess pressure. Using greater force will not make the cup brush or wire
wheel more effective, but will bend the wires out of shape and damage the
brush.
WARNING:
Remove the Battery (8) and Blade when the tool is to be
left unattended.
Accessories
• A full range of accessories including discs, wire brushes and
guards, is available from your Silverline stockist
•
Spare parts can be obtained from toolsparesonline.com
Maintenance
WARNING:
Always disconnect the tool from the power supply, before
cleaning or carrying out maintenance.
General inspection
• Regularly check that all the fixing screws are tight. They may
vibrate loose over time
• Repairs should be carried out by an authorised Silverline
service centre.
Lubrication
•
Lubricate all moving parts with a suitable lubricant spray, at
regular intervals
Cleaning
WARNING:
ALWAYS wear protective equipment including eye
protection and gloves when cleaning this tool.
• Keep your tool clean at all times. Dirt and dust will cause
internal parts to wear quickly, and shorten the device’s
service life
•
Clean the body of your tool with a soft brush, or dry cloth
• Never use caustic agents to clean plastic parts. If dry
cleaning is not sufficient, a mild detergent on a damp cloth
is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
•
If available, use clean, dry, compressed air to blow through
the ventilation holes (where applicable)
Brushes
•
Over time the carbon brushes inside the motor may
become worn
•
Excessively worn brushes may cause loss of power,
intermittent failure, or visible sparking
• If you suspect that the brushes may be worn, have them
replaced at an authorised service centre
Contact
For technical or repair service advice, please
contact the helpline on (+44) 1935 382 222
Web: silverlinetools.com/en-GB/Support
UK Address:
Toolstream Ltd.
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
EU Address:
Toolstream B.V.
De Keten
00004
5651 GJ
Eindhoven, Netherlands