![background image](http://html1.mh-extra.com/html/silverline/282400/282400_manual_1273481011.webp)
Air Framing Nailer 90mm
282400
11
silverlinetools.com
Operation
WARNING:
ALWAYS wear appropriate personal protective equipment, including eye protection
when working with this tool .
Adjusting the depth of penetration
• The Depth Adjuster (10) enables you to adjust the depth of nail penetration
• Rotate the Depth Adjuster a small amount at a time (clockwise to increase depth, anticlockwise
to decrease depth) (Fig. VII) and test by firing a nail into a waste piece of material, until the nail
head penetrates by the amount required
Firing nails/staples
IMPORTANT.
Before firing a nail into the workpiece, always test the depth of penetration on a piece
of scrap material . See ‘Adjusting the depth of penetration’ below .
See Fig. VIII
1. Connect the tool to the air supply
2. Rotate the Air Exhaust (12) so that air escapes in a safe direction (away from the operator)
3. Hold the tool firmly against the material so that the Safety Catch (9) is depressed
4. Gently squeeze the Trigger (11) until the fastener is fired
5 . Release the Trigger and remove from the workpiece
6. Check that the fastener has penetrated the material correctly
Accessories
• A full range of accessories including nails and staples is available from your Silverline stockist
• Spare parts can be obtained from toolsparesonline .com
Maintenance
WARNING:
ALWAYS disconnect the tool from the power supply before carrying out any
inspection, maintenance or cleaning .
General inspection
• Regularly check that all the fixing screws are tight. They may vibrate loose over time
Lubrication
• Lubricate all moving parts with a suitable lubricant spray, at regular intervals
Cleaning
WARNING:
ALWAYS wear protective equipment including eye protection and gloves when
cleaning this tool .
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the device’s service life
• Clean the body of your tool with a soft brush, or dry cloth
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent
on a damp cloth is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
• If available, use clean, dry, compressed air to blow through the ventilation holes (where
applicable)
Keep the tool oiled
IMPORTANT:
Ensure air tools are kept clean and lubricated. Lubrication is essential to prevent
corrosion of internal parts, which could lead to tool failure .
• Contact your retailer for suitable air tool oil. DO NOT UNDER ANY CIRCUMSTANCES USE NORMAL
ENGINE OIL
Every day, before use:
• With the tool disconnected from the air supply, pour the 1-2 drops of oil into the Quick Connector
(or air intake)
• Operate the tool briefly (e.g. 2-4 seconds) at low speed to lubricate all internal workings
Once a week:
• Wipe the body of the tool with a damp cloth. You can use a mild detergent or non-flammable
solvent
• Once clean, lubricate all moving parts with a light oil
Note:
If the tool is in constant use or used for long periods at a time a combined filter/lubricator
must be fitted. There must be an air filter fitted at all times.
• Failure to comply with the operating and maintenance instructions may invalidate the guarantee
Clearing jams
• Using the Hex Keys supplied and a 10mm spanner (not supplied), the magazine and firing
mechanism can be disassembled to clear blockages or jams
• To disassemble the magazine and firing mechanism
1. Unscrew the two 3mm magazine Hex Screws (8) using the 3mm Hex Key (15)
2 . Remove the two Screws and screw plate
3. Unscrew and remove Magazine Hex Screw 5mm (10) using the 5mm Hex Key (14) (Fig. IX)
4. Unscrew and remove Magazine Hex Screw 5mm (11) using the 5mm Hex Key (14) a 10mm
spanner (not supplied) (Fig . X)
5. Taking care not to lose the magazine sliding collet (Fig. XI), CAREFULLY slide magazine out of
nailer (Fig. XII)
Note:
When the magazine is removed the Safety Catch mechanism is no longer fixed to the tool.
Ensure that the tool is positioned so that the Safety Catch mechanism will not slide off the tool.
6. Slide the spring loading mechanism out of magazine (Fig. XIII) and check both magazine and
nailer for obstructions
7. After clearing any obstruction, ensure spring loading mechanism is inserted correctly with
spring bracket hooked onto the end of the magazine (Fig. XIV)
8 . Reassemble all parts, in reverse order to removal and ensure all screws/nuts are tightened
correctly
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web:
silverlinetools .com/en-GB/Support
Address:
Toolstream Ltd
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
• Air tools should not be disposed of with household waste
• Spray guns may contain traces of solvents and paint residue, and must be recycled accordingly
• Surplus paints, solvents and cleaning solutions must be disposed of according to the
manufacturer’s instructions
• Contact your local waste disposal authority for information on the correct way to dispose of
air tools
282400_Manual.indd 11
30/08/2019 09:52
Содержание 282400
