
38 GB
9.4 Switching on/off and
reverse mode
• To turn on the device, set the on/off
switch
12
to
1
.
• To turn off the device, set the on/off
switch
12
to
0
.
• If you set the on/off switch
12
to
R
, you
will start reverse mode. With this func-
tion you can eliminate small blockages.
9.5 Removing blockages
If a piece of fruit or vegetable is blocking the
auger
5
, it must be removed immediately.
You can recognise a blockage...
… if no more juice comes out of the
juice outlet
9
, even though pieces of
food are still in the chute.
… if the pieces of food in the food
chute
3
no longer slide down,
… if there are unusual sounds, or
… if the motor becomes audibly slower.
Reverse mode
First, try to fix the blockage by using reverse
mode:
1. Set the on/off switch
12
in sequence
to
0
, for approx. 2 seconds to
R
(re-
verse mode) and again to
0
.
2. Turn the on/off switch
12
to
1
. Check
whether the device is working normally.
3. Repeat the process, if necessary.
Cleaning the device
If this does not resolve the blockage, follow
these steps:
1. Pull out the mains plug
11
.
2. Take the device apart (see “Disassem-
bly” on page 38).
3. Clean the auger
5
, the holder
7
, the
screen assembly
6
and the working
container
8
(see “Cleaning” on
page 39).
4. Reassemble the parts and proceed with
juice extraction.
10. Preparing a sorbet
WARNING! Risk of material dam-
age!
~
The device is designed to prepare sor-
bet for up to 5 minutes maximum oper-
ating time without interruption. After
this, the device must remain switched off
until the base unit
13
has completely
cooled down.
1. Assemble the device for sorbet prepa-
ration (see “Insert the sorbet assembly”
on page 35).
2. Prepare
half
frozen fruit pieces (see
“Preparing food for sorbet prepara-
tion” on page 36).
3. Proceed in the same way as for juicing.
The finished sorbet is ejected through
the juice outlet
9
.
4. Mix the sorbet again with a spoon and
serve it immediately.
11. Disassembly
DANGER! Risk of electric
shock!
~
Pull the mains plug
11
out of the wall
socket before you disassemble and
clean the device.
1. Pull the food pusher
1
off upwards
from the food chute
3
.
2. Remove the filling aid
2
.
3. Turn the lid
4
anticlockwise until
the point
symbol
•
points to the
opened lock symbol
. Remove the
lid
4
.
4. Close the drip stopper
10
.
5. Pull out upwards the screen assembly
6
/
sorbet assembly
19
complete with the
auger
5
. While doing this, move these
parts somewhat back and forth to
make them easier to release.
__331036_Slow Juicer_B8.book Seite 38 Donnerstag, 7. November 2019 12:33 12
Содержание 331036 1907
Страница 49: ...47 GB __331036_Slow Juicer_B8 book Seite 47 Donnerstag 7 November 2019 12 33 12 ...
Страница 121: ...119 PL __331036_Slow Juicer_B8 book Seite 119 Donnerstag 7 November 2019 12 33 12 ...
Страница 143: ...141 CZ __331036_Slow Juicer_B8 book Seite 141 Donnerstag 7 November 2019 12 33 12 ...