29
GB
5. Before using for the first time
• Remove all packing material.
• Check that the device is undamaged.
5.1 Remote control
Initial use
• Remove the transport lock from the battery compart-
ment and remote control.
Changing the battery
DANGER OF EXPLOSION!
If the battery is not
correctly replaced. Replace only with the same or
an equivalent type.
1.
FIGURE A:
open the battery compartment lid by un-
locking it and sliding it in the direction of the arrow.
2. Replace the old battery with a new one.
WARNING!
Ensure the correct polarity of the bat-
tery. The plus sign on the battery must be visible.
3. Close the battery compartment again.
5.2 Setting up / Wall mounting
NOTE:
if you connect the device to a television set, place
the device as centrally as possible below the set.
Setting up
1. Place the device on a level surface.
2. Connect the power unit
7
to the device.
Wall mounting
WARNING! Risk of material damage!
~
Please ensure the following when mounting on a wall:
- The fixing material must be matched to the proper-
ties of the wall. If necessary, use fixing material other
than that supplied.
- Make sure that in the installation location there are no
pipes or cables in the wall (e.g. electricity, water, gas).
- If necessary, have the wall mounting carried out by
an expert.
1.
FIGURE B:
drill 2 holes at the same height at a dis-
tance of 40 cm apart. Use the attached drilling tem-
plate
30
where appropriate.
2. Insert the rawlplugs
29
into the drill holes.
3. Tighten the screws
28
in the rawlplugs
29
.
4. Insert all of the cables used into the connections (see
“Connections” on page 29).
NOTE:
in the case of wall mounting, use a jack max. 3 cm
in length for the optical input
OPTICAL IN
11
(and if nec-
essary a TOSLINK angle adapter) to prevent the cable
from kinking and avoid possible damage.
5. Connect the power unit
7
to the device.
6. Suspend the device on the screws
28
with the wall
brackets on the back.
5.3 Connections
CAUTION:
make sure that the soundbar and the devices
to be connected are switched off before you connect them.
Please also read the operating instructions for the devices
which you are connecting.
• A subwoofer can be connected to the cinch socket of
the
SUB OUT
10
output. This is automatically con-
trolled by the device.
5.4 How to use
NOTE:
the device remains in standby mode after being
switched off. As the device still uses some electricity in this
mode, unplug the power unit
7
from the wall socket to dis-
connect the device from the mains.
• Connect the power unit
7
with an easily accessible
wall socket. The red LED
1
on the device lights up. The
device is now in standby mode.
Input
Use
Remote
control
button
LED
colour
AUX IN
9
Connection with ste-
reo cinch cable
8
,
e.g. television set,
CD player
AUX
17
white
LINE IN
6
Connection with
3.5 mm stereo jack
cable, e.g. MP3
player, telephone
LINE IN
26
green
OPTICAL
IN
11
Connection with
TOSLINK cable,
e.g. television set,
DVD player
OPTICAL
16
orange
Bluetooth
Radio connection,
e.g. smartphone
14
blue
BB58B%ERRN6HLWH)UHLWDJ-XQL
Содержание 113896
Страница 35: ...33 GB BB58 B ERRN 6HLWH UHLWDJ XQL ...
Страница 36: ...BB58 B ERRN 6HLWH UHLWDJ XQL ...
Страница 37: ...BB58 B ERRN 6HLWH UHLWDJ XQL ...
