background image

 

18 

 

Calibration

 

 
Nozzle Sets for Typical Spraying Applications

 

The  nozzle  sets  in  the  following  four  examples  are  suitable  for  typical  applications  when  spraying 
grapes, orchard fruits at either low or high spraying volume, or citrus fruits. 

 

1. Grapes

 

Application rate  

600 l/ha 

 

Travel speed 

 

5 km/hr 

 

Row width 

 

3.0 m 

 

Spraying pressure 

15 Bar 

 
 
 
 
 
 

NOZZLE SET FOR TYPICAL GRAPE SPRAYING APPLICATION    (600 l/ha) 

Nozzle Position     

from top down 

Jet/Swirl Plate Size 

Closed  Closed  1.0/CC  1.0/CC  1.0/CC  1.0/CC  1.0/CC  Closed  

 
To provide a substantially horizontal spray pattern to suit vines the jets in positions 1, 2 and 8 are 
closed by flipping the nozzles through 90 degrees so that neither of the jets is facing outwards, 
refer diagram on page 14. 

 

The fitment of the same sized 1.0 jet and Closed Centre swirl plate (CC) in each of the nozzle 
positions from 3 to 7 will produce a uniform density within the spray pattern. An alternative nozzle 
arrangement would be to use HCC02 (Orange) in positions 3-7 at 11 bar pressure. 

 

2. Orchard Fruits - Low Volume Spraying

 

Application rate  

1000 l/ha 

 

Travel speed 

 

5 km/hr 

 

Row width 

 

6.1 m 

 

Spraying pressure 

20 Bar 

 
 
 

         1000 x 5 x 6.1   = 51 l/min 

 

 

 

 

 

    600 

 
 
 
 
 
 
 
 
This arrangement will produce a spray pattern with approximately 70% of the output discharging from 
the four centre jets Nos. 3, 4, 5 and 6. Refer to the Standard Jet Set Chart on page 17 for details of 
the output from each nozzle combination of disc and swirl plate at various pressures. An alternative 
nozzle setup using HCC Hollow cone would be as below with pressure at 16 bar. 
 

 
 
 
 
 

Total Application Rate (l/min)  = 

Application rate (l/ha) x Speed (km/hr) x Row width (m)  
                                       600  

 

600 x 5 x 3 
     600 
 

= 15 l/min 
 

Total Application Rate (l/min)  = 

Application rate (l/ha) x Speed (km/hr) x Row width (m)  
                                       600  

 

 

                     

 

Nozzle Position     

from top down

1

2

3

4

5

6

7

8

Jet/Swirl Plate Size

0.8/CC

1.0/1.0

1.5/1.2

1.5/1.2

1.5/1.2

1.2/1.0

1.0/1.0

1.0/1.0

NOZZLE SET FOR TYPICAL LOW VOLUME SPRAYING APPLICATION    (1000 l/ha)

Nozzle Position     

from top down

1

2

3

4

5

6

7

8

HCC Hollow Cone

HCC015 HCC025 HCC05

HCC05

HCC05 HCC035 HCC025 HCC025

NOZZLE SET FOR TYPICAL LOW VOLUME SPRAYING APPLICATION    (1000 l/ha)

Содержание Stiletto 2000L





























Отзывы: