manualshive.com logo in svg

Silicon Laboratories Si4430, Руководство пользователя

Поделиться
Скачать
Silicon Laboratories Si4430 Скачать руководство пользователя страница 109

Si4430

Preliminary Rev. 0.4

109

Reset value = 10001101

Register 30h. Data Access Control

Bit

D7

D6

D5

D4

D3

D2

D1

D0

Name

enpacrx

lsbfrst

crcdonly

Reserved

enpactx

encrc

crc[1:0]

Type

R/W

R/W

R/W

R/W

R/W

R/W

R/W

Bit

Name

Function

7

enpacrx

Enable Packet RX Handling. 

If FIFO Mode (dtmod = 10) is being used automatic packet handling may be enabled. 
Setting enpacrx = 1 will enable automatic packet handling in the RX path. Register 
30–4D allow for various configurations of the packet structure. Setting enpacrx = 0 will 
not do any packet handling in the RX path. It will only receive everything after the sync 
word and fill up the RX FIFO.

6

lsbfrst

LSB First Enable. 

The LSB of the data will be transmitted/received first if this bit is set.

5

crcdonly

CRC Data Only Enable. 

When this bit is set to 1 the CRC is calculated on and checked against the packet data 
fields only.

4

Reserved

Reserved.

3

enpactx

Enable Packet TX Handling. 

If FIFO Mode (dtmod = 10) is being used automatic packet handling may be enabled. 
Setting enpactx = 1 will enable automatic packet handling in the TX path. Register 30–4D 
allow for various configurations of the packet structure. Setting enpactx = 0 will not do 
any packet handling in the TX path. It will only transmit what is loaded to the FIFO.

2

encrc

CRC Enable. 

Cyclic Redundancy Check generation is enabled if this bit is set.

1:0

crc[1:0]

CRC Polynomial Selection.

00:

CCITT

01:

CRC-16 (IBM)

10:

IEC-16

11:

Biacheva

Содержание Si4430

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды