Silicon Laboratories EM3585 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 25

Silicon Laboratories EM3585 Скачать руководство пользователя страница 13

EM358x

Table 6.1. EM358x Pin Descriptions (Continued)

Rev 1.0

43

Pin #

Signal

Direction

Description

26

PA4

I/O Digital

I/O

ADC4

Analog

ADC Input 4
Select analog function with GPIO_PACFGH[3:0]

PTI_EN

O

Frame signal of Packet Trace Interface (PTI)
Disable trace interface in ARM core
Enable PTI in Ember software
Select alternate output function with GPIO_PACFGH[3:0]

TRACEDATA2

(see also Pin 36)

O

Synchronous CPU trace data bit 2
Select 4-wire synchronous trace interface in ARM core
Enable trace interface in ARM core
Select alternate output function with GPIO_PACFGH[3:0]

27

PA5

I/O Digital

I/O

ADC5

Analog

ADC Input 5
Select analog function with GPIO_PACFGH[7:4]

PTI_DATA

O

Data signal of Packet Trace Interface (PTI)
Disable trace interface in ARM core
Enable PTI in Ember software
Select alternate output function with GPIO_PACFGH[7:4]

nBOOTMODE

I

Activate FIB monitor instead of main program or bootloader when coming
out of reset.
Signal is active during and immediately after a reset on nRESET. Refer to
section 7.5, Boot Configuration, in Chapter 7, GPIO, of the

Ember EM358x

Reference Manual

for details.

TRACEDATA3

(see also Pin 38)

O

Synchronous CPU trace data bit 3
Select 4-wire synchronous trace interface in ARM core
Enable trace interface in ARM core
Select alternate output function with GPIO_PACFGH[7:4]

28 VDD_PADS Power

Pads

supply

(2.1–3.6

V)

29

PA6 I/O

High

cur-

rent

Digital I/O

TIM1C3

O Timer

1

channel

3

output

Enable timer output in TIM1_CCER
Select alternate output function with GPIO_PACFGH[11:8]

TIM1C3

I Timer

1

channel

3

input

Cannot be remapped

Note:

1.

IRQC and IRQD external interrupts can be mapped to any digital I/O pin using the GPIO_IRQCSEL and
GPIO_IRQDSEL registers.

«
...
11
12
13
14
15
...
»

Содержание EM3585


























Отзывы:

Нет отзывов