Silicon Graphics UV 20 Скачать руководство пользователя страница 60

Страница: 60 / 70

007-5900-001

A: Power and Environmental Specifications

Wattage Limitation of the PCI Loading

Table A-2

summarizes the wattage limitation of the PCI loading.

Environmental Specifications

Table A-3

lists the system-level operation and non-operating environmental limits.

Table A-2

Wattage Limitation of the PCIe Loading

VIN

Power Supply Configuration

Maximum PCI Loading

90–140VAC
(AC low-line)

1600W (1+1) redundant, hot-swap capable
1600W (1+0 or 2+0) non-redundant

260W

180–264VAC
(AC high-line)

1600W (1+1) redundant, hot-swap capable
1600W (1+0 or 2+0) non-redundant

450W

Table A-3

Environmental Specifications

Attribute

Limits

Operating temperature

+10

C to +35

C with the maximum rate of change not to exceed 10

C per hour

Non-operating
temperature

-40

C to +70

Operating humidity range 20%–80%, non-condensing

Non-operating humidity

8%–80%, non-condensing at 35

Acoustic noise

Sound power:
– 3.5” HDD SKU: 6.9BA at idle and 7.4BA at active mode
– 2.5” HDD SKU: 6.5BA at idle and 7.07BA at active mode.

Shock, operating

Half sine, 2 g peak, 11 milliseconds

Shock, unpackaged

Trapezoidal, 25 g, velocity change 136 inches/second (40 lbs to less than 80
lbs)

Shock, packaged

Non-palletized free fall in height 24 inches (40 lbs to less than 80 lbs)

Vibration, unpackaged

5 Hz to 500 Hz, 2.20 g RMS random

Содержание UV 20







































































Результаты поиска

Содержание UV 20

Отзывы:

Похожие инструкции для UV 20

Бренды по названию

Популярные бренды

Silicon Graphics UV 20, Руководство пользователя системы

Результаты поиска

Содержание UV 20

Отзывы:

Похожие инструкции для UV 20

Бренды по названию

Популярные бренды