Silicon Graphics UV 20 Скачать руководство пользователя страница 35

Страница: 35 / 70

007-5900-001

Chapter 4

Chassis Maintenance

For warranty and safety considerations, SGI designates the following chassis components as
customer-replaceable units (CRUs):

•

Power supplies

•

Fans

•

Disk drives

These components are all hot-swappable; that is, you can replace them without powering down
the server. A trained service technician should install and replace all other components.

This chapter describes the following chassis maintenance activities:

•

“Removing and Installing the Front Fan Bezel” on page 23

•

“Removing the Rack Handles” on page 25

•

“Installing the Rack Handles” on page 26

•

“Removing the System Top Cover” on page 27

•

“Replacing the System Cover” on page 29

•

“Replacing the Power Supply Modules” on page 30

•

“Installing Hot-Swap Hard Drives” on page 32

•

“Replacing a Fan Module” on page 35

•

“Mounting the Chassis to a Rack” on page 39

•

“Removing the Chassis from a Rack” on page 42

Содержание UV 20







































































Результаты поиска

Содержание UV 20

Отзывы:

Silicon Graphics UV 20, Руководство пользователя системы, Страница: 35 / 70

Результаты поиска

Содержание UV 20

Отзывы: