SILENT KNIGHT 5128 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 35

background image

35

17.2 System Messages

Table 17.2-I shows the messages that could appear on the LCD of the model 5230 annunciator. You can
connect a 5230 temporarily to allow for troubleshooting.

Table 17.2-I: Explanations of Display Messages

5230 MESSAGE

EXPLANATION/ACTION TO BE TAKEN

BAD EEPROM
5230 buzzer goes on and off.

Replace the EEPROM.

REPORTING

An event is being reported to the central station.

SYSTEM NORMAL

No trouble, alarm, or other condition exists.

AC LOW

AC power has been lost. Check connection to AC power source.

TROUBLE DIALER

The dialer has made the programmed number of attempts (programmed in
steps 30 and 34) and has not been able to communicate with the central
station. (This is a dialer failed condition.)

TROUBLE LINE 1

A trouble condition exists on phone line 1.

TROUBLE LINE 2

A trouble condition exists on phone line 2.

TROUBLE (ZONE 1-4)

A trouble condition exists in the indicated zone. If you need help locating the
trouble, refer to Section 17.1 for information about zone troubleshooting
mode (mode 25).

ALARM ZONE 1-4

An alarm condition exists in the indicated zone.

TRY AGAIN

A keystroke error has been made. Press

CLEAR

and enter the correct

keystrokes.

Line 2: REPORTING

The system is reporting to the central station.

Line 2: CALLING COMPUTER

Message not explicable.

TIME?

The 5128/29 is in Time Set mode.

TROUBLE (line 1)
TROUBLE ZONE # (line 2)

Sprinkler supervisory trouble.

NOTE:When step programming mode is in use and the 5230 annunciator powers up, the LCD displays

messages that describe conditions currently in effect.

18. How to Contact Silent Knight

For questions and problems with Silent Knight products, contact Silent Knight Technical Support at
800-328-0103 (or 612-493-6455). To order parts, contact Silent Knight Sales at 800-446-6444
(or 612-493-6455).

«
...
33
34
35

Содержание 5128




































Отзывы:

Нет отзывов

Похожие инструкции для 5128

Бренд: Haier Страницы: 24

Бренд: Talkswitch Страницы: 17

Бренд: Vingtor Страницы: 76

Бренд: Uniden Страницы: 24

Бренд: Polycom Страницы: 2

Бренд: Alcatel Страницы: 48

Бренд: Talkswitch Страницы: 83

8100 SMARTPHONE

Бренд: Blackberry Страницы: 230

Бренд: InFocus Страницы: 120

Бренд: Avaya Страницы: 4

Бренд: Alcatel Страницы: 2

Бренд: Plum Страницы: 24

Бренд: Alcatel Страницы: 84

Бренд: OneTouch Страницы: 40

Бренд: DDM Brands Страницы: 74

Бренд: Verizon Страницы: 10

IP Pathfinder S

Бренд: Fujitsu Страницы: 28

IP Centrex SRS-12i

Бренд: Fujitsu Страницы: 69

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды