SILENT KNIGHT 5128 Скачать руководство пользователя страница 2

Страница: 2 / 35

Features

(continued from previous page)

•

Active high, contact closure or direct monitoring input for monitoring control panel’s primary power.

•

Compatibility with many Underwriters Laboratories (UL) Fire Listed receivers. (See Section 1.3 for list.)

•

Housed in plastic enclosure (8-5/8 x 4 x 1-3/8 inches) for mounting inside control panel. (Refer to the
installation manual of the compatible control panel you are using for 5128 mounting instructions.)

•

Model 5129 housed in metal enclosure (10 x 10) with AC monitoring transformer.

1.2 Optional Devices

The following accessories are available for use with the 5128/29:

•

Model 5230 Remote Annunciator. Can be temporarily connected to the system for programming and
troubleshooting only. Only one model 5230 can be used.

•

Cable for 5230, P/N 130294.

•

Model 9230 Step Transformer. Required for AC monitoring if the control panel used does not have a
distinctive AC trouble output.

1.3 UL Fire Listed Receivers

The following UL Listed receivers are compatible with the 5128/29:

RECEIVER

FORMATS

Silent Knight Model 9000

BFSK14
BFSK23
FSK
SK 3/1
SK 4/2
SIA8
SIA20

Osborn & Hoffman Quickalert

SK 3/1
SK 4/2
SIA8
SIA20
BFSK14
BFSK23

Ademco 685

SK 3/1
SK 4/2

FBI CP220

SK 3/1
SK 4/2

Radionics D6500

BFSK 1400
BFSK 2300

Содержание 5128




































Результаты поиска

Содержание 5128

Отзывы:

Похожие инструкции для 5128

Бренды по названию

Популярные бренды

SILENT KNIGHT 5128, Руководство пользователя

Результаты поиска

Содержание 5128

Отзывы:

Похожие инструкции для 5128

Бренды по названию

Популярные бренды