Signode BXT 10 Скачать руководство пользователя

Страница: 7 / 19

05.07

Flashing

green light

Continuous

green light

Continuous

green light

Flashing

green light

Double fl ashing

green light

No indicator illu-

minated

4.4 BATTERY CHARGER INDICATORS

Ready for charging

Battery not inserted, mains

supply is connected.

Rapid charging

Rapid charging operates

until the battery is fully

recharged. The battery

charger then switches

automatically to trickle

charging.

Trickle charging

Battery is fully charged.

The battery charger is

delivering only a trickle

charge.

Temperature

Warning

: the battery is too

hot (or too cold). Trickle

charging only.

The battery charger

switches automatically to

rapid charging when the

temperature is within the

permitted range again.

Error message

Warning

: battery cannot

be charged (battery or

temperature sensor

defective or not a BOSCH

battery).

Mains supply not

connected:

electrical plug, cable or

battery charger defective.

For detailed information, refer to the operating

instructions for the battery charger.

Fig. 4

BUY AT ALLSTRAP (866) 779-2673

Содержание BXT 10




















Результаты поиска

Содержание BXT 10

Отзывы:

Похожие инструкции для BXT 10

Бренды по названию

Популярные бренды

Signode BXT 10, Руководство по эксплуатации, частям и безопасности

Результаты поиска

Содержание BXT 10

Отзывы:

Похожие инструкции для BXT 10

Бренды по названию

Популярные бренды