background image

17

05.07

WARNING

Inspect all parts daily and replace them if they  are worn or broken. Failure to do this can affect 

a product’

s operation and could result in 

serious personal injury

.

91

86

54

58

60

54

73

55

57

54

a)

45

53

49

a)

85

70

69

68

67

66

80

10

12

13

17

14

22

23

28

27

30

a)

34

35

36

37

38

36

100

a)

105

138

139

135

140

141

137

136

142

63

78

77

65

75

79

(83)

(81)

84

a)

85

(a)

88)

(89)

(82) 

a)

72

77

a)

74

74

124

123

120

a)

153

5

40

a)

47

43

10 mm (3/8")

a)

47

46

1

a)

156

155

11

5

3

4

8

11

3

c)

111

109

11

4

7

a)

11

9

11

2

94

95

96

 a)

156

86

93

(87)

90

121

7

6

5

4

3

2

1

156

162

172

170 

162

158

176

171

160

164

166

167

168

162

177

154

148

147

146

150

152

149

151

a)

156

127

11

6

11

7

11

8

130

07.03.07

BXT

 10     

 

 

a)

103

a)

Loctite 222   

b)

Loctite 243   

c)

Loctite 638     *Optionen/Options 

a)

47

102

13 mm (1/2")

141

a)

131

126

11

7

42

88

104

10 mm (3/8")

16

41

190

175

173

191

18

19

20

200*

196*

a)

125

133

132

134

97 (incl. 81,82,83,87,88,89)

BUY AT ALLSTRAP (866) 779-2673 

Содержание BXT 10




















Отзывы: