background image

6

8860 Dual Channel Conductivity/Resistivity Controller 

Select CUSTOM only if you are connecting a certi

fi

 ed conductivity sensor.  Select 

STANDARD for all non-certi

fi

 ed sensors.

For STANDARD sensors:  Select the nominal cell constant:   0.01, 0.1, 1.0, 10.0 or 20.0.

For CUSTOM sensors:  Enter the precise cell constant from the certi

fi

 cate provided with your 

sensor, or from the information label on the sensor.

Adjust the temperature of the system based on an accurate external reference.

This single-point wet calibration procedure requires a test solution of known value.

Enter all zeroes here to restore TEMPERATURE and CONDUCTIVITY to factory calibration.

Select the units of measure:  

μ

S/cm, mS/cm, k

Ω

•cm, M

Ω

•cm, PPB, PPM

If the Units selection is PPM or PPB, set the ratio of 

μ

S to Total Dissolved Solids.  The factory 

preset value is  2 

μ

S per 1 PPM of TDS. (Always 

μ

S/PPM, even if units is PPB).

See page 10 for additional information.

Select a functional relationship between C1 and C 2:     •  Ratio is (C1:C2) or (C2:C1)

•  Percent Reject is 100%(1-C2/C1) or 100%(1-C1/C2)  •  Difference is (C1-C2) or (C2-C1) 

Select the measured value or calculated FUNCTION you want Loop 1 to represent:

Chan 1 Cond, Chan 2 Cond, Chan 1 Temp, Chan 2 Temp, or Function

Set the minimum (4 mA =) and maximum (20 mA =) range for Loop 1.

Make sure that the values are consistent with the units of the source.

Select operating mode for Relay 1:  OFF, LOW, HIGH, USP or PULSE.

For USP mode: •  Relay 1 SOURCE must be Cond 1 or Cond 2

 

 

•  Temp Comp (Options menu) must be set to None 

Select the INPUT SIGNAL (or FUNCTION) monitored by Relay 1:

• Cond 1 

• Cond 2     

  

• Temp 1       

• Temp 2       

•  Function

Set  Relay 1 activation point.  The maximum value acceptable is 999999.

USP setpoints are high alarms, where the setpoint is a percentage below the USP limit.

Relay 1  will be deactivated at setpoint ± Hysteresis (depending on High or Low selection).

When the relay Mode is USP (de

fi

 ned as a HIGH alarm), Hysteresis is displayed in 

μ

S.

Set up to 6400 seconds delay time for relay response.

Relay 1 will be activated only if the source value exceeds the setpoint for this time period.

If Relay 1 is PULSE mode, set the start and end point of the conductivity range and also set 

the maximum pulse rate.  (The maximum PULSE rate setting is 400 pulses per minute.)

The combined Relay 1 Range and Pulse rate settings shown here indicate:

"Start pulsing when the conductivity value is 10 

μ

S and increase the pulse rate  up to the 

maximum of 120 pulses per minute when the conductivity value reaches 40 

μ

S"

Use this "notepad" to record important dates, such as annual recerti

fi

 cation or scheduled 

maintenance.

Chan 1 Cell:

 Standard  >

Chan 1 Cell:

 1.0  >

Cell: Custom

 1.0000  >

Chan 1 Set:

Temperature >

Chan 1 Set:

Conductivity >

Chan 1 Units:

 uS/cm  >

Chan 1 TDS:

2.0000 uS/PPM 

>

Function:

 Reject 

C1 

 C2 

>

Loop 1 Source:

 

Chan 1 Cond 

>

Loop 1 Range: uS

 0.0000 

 100.000  >

Relay 1 Mode:

 Low  >

Relay 1 Source:

 

Chan 1 Cond 

>

Relay 1 Setpnt:

 10.0000 

uS  >

Relay 1 Hys:

 0.5000 

uS  >

Relay 1 Delay:

 10.0 

secs  >

Relay 1 Rng: uS

 10.0000 

 40.0000  >

Relay 1 PlsRate:

120 Pulses/Min 

>

Last CAL:

 04-20-08  >

Calibrate Menu

Display

(Factory settings shown)

Description

•  All changes in this menu become effective when saved, except the "Set Cond" and "Set Temp" settings.
•  All outputs affected by a change in the  "Set Cond" and "Set Temp" settings are frozen until you exit the Calibrate menu.

Содержание 8860













Отзывы: